Troubleshooting BMW Airbag Light Problem
BMW airbag light on and won't turn off? In this article, you will learn how to troubleshoot BMW airbag light yourself. Find out what are some of the most common problems that can trigger the airbag light. How to reset BMW airbag light. BMW airbag light may also be referred to as SRS light (Supplemental Restraint System). If the airbag light stays on in your BMW it can be due to several reasons:
- BMW was involved in an accident
- Faulty passenger occupancy sensor/mat
- Fault code stored in airbag module due to low battery voltage
- Stuck seat belt buckle
- Defective seat belt pre-tensioner
- Malfunction with one of the airbag modules
- Damaged ignition switch
If your BMW is under warranty, have your BMW dealer diagnose the problem free of charge. If your BMW is out of warranty, it can get costly to troubleshoot and fix airbag problems. Don't panic! We will show you how to diagnose airbag light yourself using various BMW airbag scan tools.
- Symptoms, Warning Messages
- BMW Airbag Light Reset
- Instructions on how to read BMW Airbag Codes
- BMW Airbag Light Reset Using Carly for BMW
- BMW Airbag Light Reset Using other Scan Tools
- Common Causes BMW Airbag Light
- BMW AirBag Scan Tool
- BMW Airbag Recall
- BMW Airbag Light Repair Cost
- Frequently Asked Questions
1. Symptoms, Warning Messages
Symptoms that BMW drivers notice when the BMW airbag light is on.
- Airbag SRS Light Illuminating on Dashboard
- Pass. Restraint System Message
"Fault in passenger restraint system affecting airbag, belt tensioner or belt force limiter. Continue to wear seat belt. Please contact the nearest BMW center."
- Restraint System Message
"Function of the airbag, belt tensioners and belt force limiters faulty. Ensure seat belt is fastened despite the fault. Have the problem checked by the nearest BMW service. "
- Intermittent airbag light
Airbag light may turn on and off randomly.
2. BMW Airbag Light Reset
If the airbag light is on, the first thing you need to do is read codes from the airbag module. This procedure is very simple and anyone can perform this procedure in less than 20 minutes. No need to take your BMW to the dealer to diagnose the airbag light when you can do it yourself. We don't recommend replacing parts without reading the codes first. The airbag/srs light can be on for many reasons, and without pulling the codes, you are only guessing. Retrieving SRS codes on a BMW is very easy.
Follow these instructions to read and clear codes from the airbag control unit on a BMW. The instructions apply to all 2002 and newer BMWs including 1-Series, 3-Series, 5-Series, X1, X3, X5 etc.
What you will needBack to top
3. Instructions on how to read BMW Airbag Codes
In this guide, we will show you how to read and clear codes on a BMW using Foxwell NT510 for BMW. If you like to learn how to read BMW airbag codes using a different BMW Scan Tool, review this article on How to read BMW codes.
Locate OBD-2 port under the dash. Connect your scanner to the OBD2 port. If your BMW is 2001 or older, you will need an 20 pin to OBD2 adapter.
Turn on ignition. Don't start the engine.
The scanner will turn on. Select your BMW chassis/model on the scanner.
Select BMW - Control units - Body - Safety System. Once you navigate to Safety System /SRS control unit you can read Airbag Fault Codes.
Clear codes from the airbag control unit. Go back one menu. Scroll down to Clear Fault Codes. Press YES in the next screen.
- Airbag codes can only be erased if the code is in stored status. Meaning the fault is stored in the memory of the SRS unit but the problem itself no longer exists.
- If you didn't fix the problem that triggered the airbag light/code, you would not be able to clear the codes. They will return as soon as you restart the car. Read the codes again and fix the problem. Then reset the airbag light again.
- Most airbag fault codes require a scan to clear the code and reset the light. In very few certain circumstances, the airbag light will turn off once you fix the underlying problem without the need of scan tool.
- Disconnecting the battery will not reset airbag light or clear codes stored in the airbag control module/SRS system. Generic OBD2 code readers can not clear BMW airbag light.
- Always disconnect the battery before working on any airbag component.
- When handling airbags always keep your body two feet away from the airbag.
4. BMW Airbag Light Reset Using Carly for BMW
In this video, you will learn how to read and clear BMW airbag light using Carly for BMW .Back to top
5. BMW Airbag Light Reset Using other Scan Tools
If you would like to know how to read and clear BMW airbag light using other scanner watch videos in this article:Back to top
6. Common Causes BMW Airbag Light
Without reading the codes, there is no easy way to know the reason why BMW airbag light is on. With that said, there are a few common causes and trouble spots that often trigger BMW airbag light. We don't recommend replacing parts without pulling the airbag codes first.
Passenger's occupancy sensor
The #1 common issue causing BMW airbag light to come on is due to a defective passenger seat weight sensor (also referred as the occupancy sensor, child sensor, passenger mat, seat sensor pad).
The sensor is installed under the passenger seat cushion and detects if the passenger is over a certain weight. If the person is not over the weight limit (ex. a child), the passenger airbag will not deploy in case of an accident because it can cause injuries to the child. This sensor fails very frequently and is often the culprit.
Usually, if the seat occupancy sensor is defective on your BMW, you will get a warning on your iDrive screen with a message stating that there is passenger airbag problem or passenger airbag off.
To fix this problem, it requires the removal of the seat and seat cushion. At the dealer, this problem will cost you $500+. If you have DIY skills, you can replace the passenger seat sensor yourself. A replacement passenger seat mat sensor can be purchased online for under $200. Check out these listing of BMW Passenger Weight Sensor. To replace the passenger weight sensor yourself you will need a few basic tools and about two hours.
Many BMW owners install what is called a BMW Passenger Sensor Bypass. It tricks the airbag system to think that the sensor is working properly. It is important to understand that if you install a BMW weight sensor bypass, the passenger airbag will deploy in case of an accident. Even if there is no passenger or a child is sitting in the passenger seat. For this fix, you will need BMW Seat Occupancy Emulator Bypass plus you will need to clear the fault codes after installation. Installing the sensor is simple as it plugs right under the passenger seat. In some countries, it may be illegal to modify the restraint system. Perform this modification at your own risk!
Undervoltage or Airbag light on after changing the battery
The airbag light on BMW may stay on if you replace the car battery. Often an under-voltage fault (supply voltage) code is stored in the SRS control unit. It is because either the old battery was no longer providing the required voltage (voltage dropped under 12 volt) or you disconnected the battery while the key was in the ignition. There will be stored codes in the airbag module but they can be cleared using a BMW airbag scan tool.
Follow these instructions to learn How to replace BMW battery and register it yourself.
Seat Belt Buckle
Another reason why the airbag light may stay on is the seat belt buckle defective. Inside the seat belt buckle is a small switch that can fail. When you start the car, it can detect that you are in the seat but the airbag control unit may not be getting a signal from the seat belt buckle. Try pressing the seat belt buckle a few times and check if the airbag light turns off. In some cases, the seat belt may not latch when inserted into the buckle.
Seat Belt Pre-tensioner
A common problem that triggered air bag light is BMW seat belt pre-tensioner. The pre-tensioner is used to tighten the seat belt in case of an accident. If the driver or passenger pre-tensioner fail, it will trigger the airbag light. A BMW pre-tensioner takes about one to two hours to replace. When you read SRS fault codes you will get fault codes pointing to the pre-tensioner.
Airbag light after crash
If your BMW was involved in an accident, the airbag light will stay on. Even if you replace the airbag that blew, the light will stay on. Crash data is stored in the airbag control unit, and cannot be cleared even with a BMW airbag scan tool. To fix this problem, you have two options. You can replace the airbag control unit on your BMW which can get very expensive. A cheaper alternative is to send your BMW airbag module to facilities that can Reset BMW Airbag Control Unit. They will erase the crash data from your BMW airbag computer and send the unit back to you. This solution does not require the computer to be re-programmed. Just plug and play. It is a lot cheaper than replacing the airbag module and installing a new unit.
BMW Airbag Light On, Horn won't work
If the airbag light is staying on and your horn doesn't work, it is most likely that you have a bad clock spring. Clock spring is installed in the steering column right behind the steering wheel. It requires the removal of the steering wheel to be replaced. On certain BMW such as E36 it is integrated into the steering wheel, which means it requires the replacement of the steering wheel as well. As your BMW clock spring (slip ring) starts to fail you may start hearing a strange sound (ex: rubbing sound) coming from the steering wheel as you turn it.
Disconnected Airbag Sensor
If you are working near airbag sensor and you happened to unplug the sensor while the key is in the ignition and the car is powered, you will trigger the airbag light. Always disconnect the battery when you change a window regulator or replace a front bumper. To move the window up and down to pull out the regulator, reconnect the airbag sensor before you turn the ignition on. Otherwise, there will be a fault code stored. The good news is that there are several BMW airbag scan tools to help you clear the codes yourself.
Electrical wires under the driver or passenger seat may get damaged or the electrical connection may get loose. Move the seats back and forth and rescan for codes. If the fault codes change from present to store, the problem is one of the electrical connectors. Inspect the connectors and wires to make sure they are not exposed.
Other possible causes
Related possible problems that can trigger the SRS light on BMWs include:
- Seat wiring harness
- Wires may get damaged such as the airbag wires under the seat. Airbag wires going to the door panels. Wires to the main airbag module. Check for continuity with a multi-meter. If you find a damaged wire, repair the wire and shrink wrap them.
- Side impact sensor defective
- The contacts for the side impact sensor may get corroded or loose. Unplug the electrical connector. Clean them and apply some dielectric grease.
- Front (bumper) impact sensor damaged
- Maybe the issue if the car was involved in an accident or you had work done at the front end of your BMW.
- Door wire harness
- Not a very common issue, but it can happen. The wires that connect the door to the car near the door hinges can get damaged.
- Ignition Switch Defective
- On 5-Series E39 BMWs a defective ignition switch may trigger the airbag warning light to come on.
- Aftermarket Stereo Installation
- Seat upgrade or removal
- Steering wheel removal or upgrade
- Blown Fuse
- Corroded connector
- Body or Engine work
7. BMW AirBag Scan Tool
- Carly for BMW
- Carly for BMW requires that you have a smartphone. It also requires the purchase of the Carly for BMW Pro app which costs another $60 in Google Play Store or Apple Store. It covers newer BMWs as well. It will not work on older, pre-2002 BMWs.
- Foxwell for BMW
- A handheld BMW airbag scan tool that will diagnose 2003 and newer BMWs. It is easy to use and does not require any extra hardware. Just plug it into the OBD2 port and you are ready to read and clear codes.
Peake R5/SRS-U BMW Airbag Scanner Reset Tool
Works on older BMW made from 1994-2003.
One of the cheapest BMW airbag scan tools. Comes with the 20 pin connector. It works on older BMW. Vehicle coverage is 1994 to 2003 BMWs.
8. BMW Airbag Recall
BMW has issued several recalls related to airbag problems. If your car has been affected by the recall, a BMW dealer will fix the airbag problem free of charge. Your BMW doesn't have to have an existing warranty to be covered by a recall. To check if your car has been affected by BMW airbag recall can call your dealer. Another method to check if a BMW has been recalled for airbag problems is to enter your VIN number and lookup BMW recalls by VIN. Or search for BMW airbag recalls by make and model here.Back to top
9. BMW Airbag Light Repair Cost
Diagnosing BMW airbag light at the dealer will cost you at a minimum one hour labor. Which means $120+ in most places. BMW independent repair shops may be willing to scan the codes and only charge half an hour. To fix the problem will cost you even more.
To diagnose BMW airbag light yourself you will spend in average $100 to purchase a scanner that can read BMW specific codes. Once you get the codes, you can decide if you want to fix the problem yourself or have a mechanic fix it for you. At least you will have a better understanding of what's wrong with your BMW.Back to top
10. Frequently Asked Questions
Will airbag deploy in an accident if BMW airbag light is on?
It depends. For example, if BMW airbag light is on because of a fault with the seat belt buckle, the airbags will deploy if you get into an accident.
If the airbag light is on, because there is no communication with the airbag control unit, or one of the airbag sensors is defective, there is a high chance that the airbags will not deploy in case of an accident.
Weather BMW airbag deploy or not depends on the nature of the problem. Note that if the airbag light is on, there is a chance that all airbags may deploy even during a minor accident.
Is it safe to drive BMW with the airbag light on?
While airbag light on, does not affect drivability, you may not be protected in case of an accident. It is not advised to drive a BMW with the airbag light on. The airbags may not work if you get in an accident.
Can I reset BMW airbag light by disconnecting the battery?
No. These are codes stored in the airbag control module. A BMW specific tool that can reset the airbag is required to reset the light.
BMW airbag light no codes
Make sure to use a BMW specific scanner. Generic OBD2 code readers are not capable of reading BMW airbag codes.
BMW airbag light flashing
If the airbag light on your BMW is flashing it means that the airbag control unit is either defective, not communicating or misconfigured.
BMW airbag light intermittent
If the airbag light comes on and off, it is often caused by a loose wire or contact. For example, the micro-switch in the seat belt buckle may get stuck. Another example would be a clock spring starting to wear no providing connection to the driver's airbag.
Here is a quick way to check if the problem is the clock spring. Next time you get a warning message related to the airbag system, try to see if the horn is working. If the horn has stopped working, the problem is the clock spring. Don't rule out the clock spring if the horn works. It may still be defective. Read codes from the airbag module.
How to check if BMW airbag light bulb was removed?
You can quickly check if the airbag warning light was tampered with.
- Turn the key to position II. Do not start the car. If your BMW has push start, press the start button without starting the car.
- Look for the airbag light.
- The light turns on for about five seconds then it turns off.
- If your BMW airbag light on does not come on, the airbag light bulb may have been removed or covered.
Can you reset BMW airbag light without fixing the problem?
No. If the problem isn't fixed, you can NOT clear BMW airbag codes. You can clear the codes from airbag module but they are reset right away. If you clear BMW airbag codes, as soon as you restart the car, the airbag light will turn on again.
Can I use an OBD2 code reader to clear BMW airbag light?
No. Generic OBD2 code readers can not clear BMW fault codes. You will need a scanner that can read and clear BMW specific fault codes. Read this article on Choosing the best scanner for BMW.
Will BMW pass inspection with the airbag light on?
It depends on the sate. In most states, you will pass. In a few states, you can't because they require the airbag light to be off. The airbag warning light has a different computer (SRS Control UNit) and does not store a code on the Engine Control Unit ECU. When a car is taken in for inspection, state inspection stations only scan for codes in the ECU.
BMW airbag light on after cleaning?
It is not uncommon for the airbag light to come on if you cleaned the car. Often owners may move the front driver or passenger seat too far forward stretching the airbag wires, unplugging the connector under the seat. Check the wires and plugs under the front seats. Make sure they are secure. The light may not turn off even if you reconnect the wires because a code is stored and will often require a BMW airbag scan tool to be reset.Back to top
|... 2017 Mercedes Benz cla 250
4 hours 46 minutes ago
My 2017 Mercedes Benz cla 250 is showing to check washer fluid so i filled it also no fluid was coming out..
|2013 sprinter tail fuse
8 hours ago
Where can I find the parking light fuse on my 2013 Sprinter?
|Bmw 328 Xi battery replacement
23 hours ago
What best battery to buy
1 day ago
My problem is my Mercedes E-350 is shaking when I press on the gas. Than my transmission is not working.
|03 trailblazer throwing same codes
1 day ago
I have scanned codes P0128 and P1345. Replaced the thermostat and temp. sensor, also the cam and crank sensor.