BMW ABS Wheel Speed Sensor Problems Causes Fix

Published by YOUCANIC Automotive Experts 
Last Updated Nov 1, 2018 

If your BMW ABS, brake, DSC, DTC or ASC lights come on, along with a message on iDrive screen reminding you to get your BMW serviced, your BMW ABS wheel speed sensor may need to be replaced. Usually the three lights ABS, traction and brake light come on as soon as you start to drive. In some cases, the three lights may come on after a few minutes of highway driving.

In this guide, we take a look at BMW ABS wheel speed sensor problems, how to diagnose it and clean it. A how-to video shows you how to replace BMW ABS sensor (also referred to as BMW ABS wheel speed sensor or speed sensor for short). A BMW wheel speed monitors the revolutions of the wheel and sends a signal to the ABS/DSC module. BMW ABS sensor is used to determine wheel revolutions per minute (rpm).

🔺

Symptoms of bad BMW speed sensor

bmw abs brake dsc light on

The most common symptom of a bad BMW ABS wheel speed sensor is three warning lights on the dashboard:

  1. ABS,
  2. Brake
  3. DSC, ASC, DTC light on.  

Other symptoms may also indicate that your BMW ABS sensor is defective. Below is an extensive list of symptoms that you may notice if your BMW wheel speed sensor is bad: 

  • ABS light on
  • Anti-lock braking disabled
  • DSC or ASC light on
  • Dynamic Brake Control Disabled
  • DBC Malfunction Drive Carefully
  • Intermittent speedometer failure
  • Traction control system disabled
  • Transmission going into limp mode
  • Transmission Failsafe
  • Intermittent activation of ABS when applying brakes
  • Engine will not rev above 5,000 rpm
  • Speedometer display double of the actual speed,
  • ABS light flicking on and off
  • Check engine light on with code P0500
  • Message on iDrive asking you to service vehicle

Check engine light, odometer, cruise control and speedometer not working are possible but less likely to happen.

🔺

Diagnose ABS Wheel Speed Sensor

We strongly recommend that you use a BMW specific scanner to read codes from the ABS/DSC module or perform a full system scan.

An extra step that you can perform to verify that your BMW wheel speed sensors are working is to use the scanner to display actual value from all four of the wheel speed sensor. If you don't have a scanner available, see a mechanic for a proper diagnostic.

Things you need to know!
A generic OBD2 scanner will not be able to read / clear BMW DSC or ABS module fault codes. 

The scanner we used is a Foxwell for BMW. There are many scanners that allow you to diagnose BMW specific fault codes. Learn more about scanners that can troubleshoot BMW problems.

Before you replace the ABS sensor, consider swapping front wheel speed sensors and recheck failure codes. Clear any stored code and monitor the codes that return. 

  • Fault code has moved to the opposite wheel, it confirms the problem is the ABS sensor. 
  • Fault code remains with the same wheel/sensor, you may have a wiring issue. 

If you don't have a BMW scanner

Another method to test BMW wheel speed sensors is to use a digital multimeter and measure resistance. Remove each wheel one at a time. Disconnect the ABS sensor wire and measure the resistance of each sensor. 

test bmw abs sensorABS sensor resistance should measure around 1000 ohms. Compare all the resistance readings from all the sensors This will help you determine which has failed. Usually only one of the sensors fails at a time. It is uncommon for more than one sensor to fail.

🔺

BMW Wheel Speed Sensor Replacement

Below you will find step-by-step instructions on how to replace BMW wheel speed sensor. 

TIP - We recommend spraying penetrating oil the night before you replace your BMW wheel speed sensors. The sensor bolt can rust and be difficult to remove. If the bolt head breaks, you will need to drill a new hole and make new threads which can complicate this repair job. 

Parts

BMW Wheel Speed Sensor

 

BMW Wheel Speed Sensor

Tools

Instructions

  1. Loosen up the lug nut. Jack up the vehicle and secure it with jack stands. Remove the wheel. remove bmw wheel to change abs sensor

     

  2. Locate your BMW wheel speed sensor on the back of wheel hub. bmw wheel speed sensor location

     

  3. Trace the ABS sensor wire to the black box where you will find the connector. Open the box by the flipping top cover. bmw wheel speed sensor removal disconnect

     

  4. Disconnect the ABS weed sensor wire. The connector is held in place with two small locking tabs. Press the two tabs then pull apart the connector. Note that next to the ABS sensor you have the connector for the brake pad wear sensor. The connector for the brake pad wear sensor is white. press tabs to disconnect bmw wheel speed sensor

     

  5. Remove the bolt that secures the ABS sensor to your BMW hub. On most BMWs, this will be 5mm hex bolt.bmw wheel speed sensor location bolt size

     

  6. Remove the abs sensor wire from the front strut bracket. 
  7. Install the new BMW wheel speed sensor making sure the wire is routed correctly. If you route the wire the wrong way it will get stretched and damaged when the wheel is turned.
  8. Clean any rust from the ABS wheel speed sensor hole using a wire brush. Insert ABS wheel speed sensor into the wheel hub and screw the bolt. 
  9. Tighten the ABS wheel speed sensor bolt to 10Nm.

IMPORTANT: Once you are done with replacing the ABS sensor, start the car and turn the steering wheel all the way to the left, then all the way to the right. Repeat the procedure a couple of times. 

Once you start driving the vehicle, your ABS / DSC / TSC / Brake lights should reset, if there are no other fault codes present.

Note: The codes may still be stored in the DSC module, but they will change from Present to Stored status. 

🔺

Cleaning BMW ABS Wheel Speed Sensor

In a few cases, the tip of the sensor can collect dirt and debris which prevent the sensor from operating properly. Simply remove the sensor and clean dirt and any metal particles from the tip of the sensor.

clean bmw wheel speed sensor

Make sure to take the wheels off and look your BMW ABS speed sensor wires as well. If any of the insulation is cracked or bare wire exposed replace the sensors.   

🔺

What else can trigger BMW ABS/DSC light? 

If you replaced your BMW wheel speed sensor and you still have a fault code for a bad ABS wheel speed sensor check the following. 

  • Check wires: Check ABS speed sensor wire in the wheel well. The wires may be accidentally pinched or exposed if the insulation is damaged. Visibly check the wire from the connector to the ABS module.
  • Bad ABS Pump/Module: A defective ABS module can also be the problem causing the ABS sensor. The module is easy to replace, but the part itself is quite expensive. A cheaper solution is to remove your existing ABS module and send it for repair to a company that offers BMW ABS wheel speed sensor. 
  • Sensors: Lateral, yaw rate sensors could also cause an ABS/DSC fault.
  • Ground: Bad ground connection for ABS module
  • Cluster: Defective instrument cluster
  • Fuses/Relays: Check ABS relay and fuse
  • Brake light switch: Mounted above the brake pedal or in the master brake cylinder. 
  • Wheel bearing: Broken tooth on wheel bearing can trigger BMW Brake ABS DSC lights to come.
  • SAS: Steering angle sensor may be defective or need to be calibrated.
🔺

BMW Wheel Speed Sensor Replacement Cost Estimate

The average cost to replace a BMW wheel speed sensor at the mechanic or dealer ranges between $120-$300.

Cost to replace a BMW wheel speed sensor yourself varies between $15-$80.

🔺

BMW ABS/ASC error codes

  • 5 Right Rear Wheel Speed Sensor
  • 6 Right Front Wheel Speed Sensor
  • 7 Front Left Wheel Speed Sensor
  • 14 Solenoid Valve Relay (check fuses)
  • 15 Pressure Sensor/Pump Error
  • 21 Module Memory Failure - ABS/ASC module is faulty
  • 23 Incorrect Coding - ABS/ASC module is faulty
  • 24 Wrong Impulse
  • 30 Left Rear Wheel Speed Sensor
  • 31 Open Right Rear Wheel Speed Sensor
  • 32 Open Right Front Wheel Speed Sensor / Wheel speed sensor, front right signal implausible
  • 33 Open Left Front Wheel Speed Sensor
  • 41 Steering Angle implausible 
  • 50 Right Front Outlet Valve - ABS/ASC module is faulty
  • 51 Left Rear Outlet Valve - ABS/ASC module is faulty
  • 54 Left Front Inlet Valve - ABS/ASC module is faulty
  • 55 ASC Intake Valve - ABS/ASC module is faulty
  • 58 Gear Box Control Unit (CAN bus error)
  • 59 DMER1 (CAN bus error)
  • 61 Steering Angle Sensor Identification
  • 66 Speed Sensor Voltage Supply
  • 67 Intermittent Interference
  • 75 Engine Speed Fault from DME
  • 81 Pressure Sensor
  • 82 Open Yaw Rate Sensor
  • 86 ASC Cut-off Valve Rear Axle
  • 88 Precharge Pump
  • 89 Low Voltage
  • 90 Temporary System Deactivation
  • 94 DDE Fault/Yaw rate sensor
  • 97 Steering Angle Sensor
  • 10 Brake Light Switch
  • 108 SN Control
  • 112 Open CAN to Instrument Cluster
  • 114 Pressure Sensor Offset
  • 117 Brake Light Switch Failure
  • 118 DME Status-Internal Error
🔺

Frequently Asked Questions

I replaced my BMW wheel speed sensor, and the ABS/Brake/DSC lights are still on, why? 

It could be because the ABS sensor wiring from the connector to the ABS module are damaged or shorted. The ABS module itself may be defective. You will need to use a BMW specific scanner to read the codes in the DSC Module. 

Which BMW models have ABS wheel speed sensor? 

  • All 2000 and newer BMWs have wheel speed sensors. This includes BMW models such as 7 Series E65, Z4 E85, 5Series E60, 6 Series E63, X3 E83, 1-Series, E87, 3-Series E90, X5 E70, X6 E71, 7 Series, F01, Z4 E89, X1 E84, 5 Series F10,  F25 F06, F20, F30, I01, F32, F22, F15, F45, I12, F26, F16, F48, G11, G60, G32, F39, G02, G05, G15, G29.

Can I use a generic OBD2 scanner to diagnose my ABS light? 

  • No. Generic OBD2 scanner that can only access the Engine Control Unit (ECU) will not be able to display codes from the ABS or DSC module. 

Is ABS sensor and wheel speed sensor the same thing? 

  • Yes, ABS wheel speed sensor may sometimes be referred to as wheel speed sensor. 

ABS new wheel speed sensor won't reseat

This is a problem that you may face if you purchase an aftermarket BMW ABS speed sensor or have the wrong part number.

🔺
DIY Cost
$15-$80
Mechanic
$120-$240
Dealer
$150-$280