How to Change Nissan CVT Transmission Speed Sensor

Vehicle:   Nissan
Difficulty: ⚫⚫⚫⚪⚪
DIY Cost: $40-$150
Est. Time: 1 hr

In this guide, you will find instructions on how to change the Nissan CVT Transmission Speed Sensor. Transmission speed sensor on Nissan CVT automatic transmission may fail, cauisng shifting problems. 

It can cause hard shifting, check engine light on, or a bang when you move the shifter from Park to Drive or Reverse gears.

This transmission is installed on multiple cars, including Nissan Altima, Cube, Juke, Maxima, Murano, NV Cargo, Pathfinder, and Quest.

Symptoms

Symptoms of bad transmission speed sensor

  • Engine bangs when placed in Drive / Reverse.
  • Check Engine Light On
  • P0720 Fault Code
  • P0500 - Vehicle Speed Sensor
  • Harsh shifting
  • Cruise control stopped working.
  • Possibly Related Fault Codes
    • P0703, P0705 Range Sensor,
    • P0706, P0711, P0712, P0713, P0715,
    • P0717 Input speed sensor,
    • P0730 incorrect gear ratio,
    • P0740 torque converter,
    • P0743, P0779, P776, P0746

What you need

Procedure

There are two methods to replace the speed sensor on Nissan CVT transmission.

The first requires that you remove the battery and the starter, which will take a lot of time.

The second is to access the speed sensor from the bottom of the engine. 

  1. Jack up the vehicle or drive it on-ramps. A secure vehicle with jack stands.
  2. Remove the plastic splash shield from the bottom of the engine.
  3. Locate the transmission speed sensor. In this Nissan Quest, you can see the sensor on the engine's driver side, between the radiator and transmission housing.nissan transmission speed sensor location
  4. Disconnect the electrical connector. Use a flat screwdriver to pry the plug away from the sensor.nissan cvt transmission speed sensor
  5. Remove the 10mm bolt. Get it loose using your 10mm socket and ratchet. Next, remove the bolt by hand.nissan transmission speed sensor replacement diy guide
  6. Remove the old speed sensor from the transmission housing. There may be a tiny amount of oil leaking from the sensor hole.nissan maxima transmission speed sensor
  7. Reinstall the new sensor. Make sure it has the O-ring in place. Apply a little bit of oil on the O-ring before installation. It is not recommended to reuse the old O-ring.diy on how to replace nissan transmission speed sensor
  8. Tighten the 10mm bolt. Connect the electrical connector. nissan altima transmission speed sensor
  9. Lower the vehicle and follow the proper procedure to check the automatic transmission fluid level.

If the check engine light is on, plug an OBD2 scanner into the diagnostic port under the dashboard (driver's side) to read and clear any stored fault codes. 

Notes

  • The sensor is right below the starter. If you are accessing the sensor from underneath the vehicle, it is better to use a 1/4" ratchet and 4" extension to get to the 10 mm bolt.
  • Service manual instructions can be found here.

Input Speed Sensor Location

On Nissan vehicles equipped with the CVT transmission, the input speed sensor is located on the side of the transmission housing.

How to diagnose Nissan transmission speed sensor

A mechanic will connect an OBD2 transmission scanner that can read Nissan codes. 

  1. Locate the OBD2 port under the dashboard.
  2. Turn the ignition to position II. All dash lights will turn on.
  3. Allow the scanner to power on.
  4. Select the Automatic Transmission menu or A/T menu.
  5. Select read codes.
  6. Verify that fault codes are pointing to a faulty transmission speed sensor.

 

By YOUCANIC Automotive Experts
Nov 2020

Comments

How to Change Nissan CVT Transmission Speed Sensor In this guide, you will find instructions on how to change the Nissan CVT Transmission Speed Sensor. Transmission speed sensor on Nissan CVT automatic transmission may fail, cauisng shifting problems.  It can cause hard shifting, check engine light on, or a bang when you move the shifter from Park to Drive or Reverse gears.