/ Vehicle / Chrysler

Chrysler Key Fob Battery Replacement Instructions

By YOUCANIC Team, 17 April, 2017

In this guide, you will find step-by-step instructions, photos, and videos on how to change the battery in all Chrysler key fob remotes.

Scroll down until you find the key fob that matches yours.

In this video, you will learn how to change the battery on one of the most common Chrysler key fob remotes. This remote is used in models including Chrysler 200, 300, Sebring, Pacifica, Town and Country vans.

What you will need

Show Instructions

Step 1. Look at the back of your Chrysler keyfob. Does it have an access door? If it doesn't, you will need to release the metal key. There is a small tab that you need to press down, and the metal emergency key will slide out. Otherwise, use a flathead screwdriver to remove the back cover.

chrysler key fob battery replacement

Step 2. Use a flathead screwdriver to remove the back cover on your Chrysler keyless remote. Once the back cover is removed, you will see the battery underneath.

diy chrysler keyless remote battery replacement

Step 3. Slide-out the old battery. If you are having a hard time removing the battery, use needle-nose pliers to remove the battery.instructions on how to change battery on chrysler town country remote Slide the new battery in. Check the orientation of the battery, ensuring that you are not placing it backward.chrysler key battery change instructions The positive (+) side of the battery should be up, facing the back cover.

Step 4. Snap the battery cover back in place. how to change chrysler key fob battery yourselfPush the metal key into the slot until it clicks securely in place.diy chrysler key fob battery replacement

Step 5. Get outside the car and press the Unlock / Lock buttons. If the battery installation was performed successfully, the doors should lock/unlock.

 

The following video demonstrates how to change the battery on the Chrysler Crossfire key.

What you will need

Procedure

  1. Open the metal blade by pressing the release button on the key fob.
  2. Place your thumb in the gap created by the flipped metal key.
  3. Press the back cover away from the remote.
  4. Remove the back cover.
  5. Remove the first battery.
  6. The second battery is now exposed. Remove the second battery as well.
  7. Install two new batteries. Make sure the positive (+) is facing you.
  8. Press the back cover onto the remote.

 

Watch a video on how to change the battery on this particular Chrysler keyless entry remote. This remote is used on most Chrysler Sebring and Town & Country models.

What you will need

Procedure

  1. Use a flat to insert on the small gap on the side of the key fob.
  2. Twist the screwdriver to separate the key for the back cover.
  3. Flip over the back cover. On the back cover, you will notice the key fob battery.
  4. Use a small screwdriver for popping out the battery from the back cover.
  5. Install the new battery with the positive (+) side facing the back cover.
  6. Place the back cover on the key and press it until it clicks.

Watch a video on how to change the battery on the Chrysler three-button remote. This remote was used on many models, including Chrysler Concorde, LHS, New Yorker, Town & Country.

What you will need

Procedure

chrysler clicker remote keyless entry battery change diy
  1. Use a flat screwdriver and insert it at the end of the keyfob.
  2. Twist the screwdriver slightly to separate the keyless entry remote.
  3. Remove the two batteries from the back cover.
  4. Install two new batteries. Make sure the positive side of the battery is facing the back cover.
  5. Press the two halves of the key fob together until you hear it click.

The following key fob is used on Chrysler vehicles such as Chrysler PT Cruiser, 300M, Sebring, Concorde, LHS from 1999-2005. This key fob uses two 3V CR2016 batteries.

What you will need

Procedure

  1. Locate the small gap on the side of the key fob.
  2. Use a flat head screwdriver to pry out the key fob by twisting it at the gap.
  3. Remove the back cover of the key fob.
  4. Remove two CR2016 batteries from the back cover.
  5. Install two new batteries. Make sure the positive side (+) of the battery is facing you.
  6. Press the two parts of the keyfob together until your Chrysler key fob seals completely.
  7. Test the keyfob on your Chrysler to make sure it locks/unlocks the doors.

What Chrysler model do these instructions apply to?

These instructions on how to change Chrysler's key fob remote battery apply to model years: 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017. These instructions apply to Chrysler Grand Voyager, Lancia Grand Voyager, Ram C/V Tradesman Cargo Van, and the Volkswagen Routan.

Why won't my Chrysler key fob won't work after I changed the battery? 

Check the button cell battery. Make sure it is not installed backward. The negative side of the button cell battery should face the circuit board of the keyfob. 

Also, there are a couple of small metal contacts that are supposed to touch the battery. Make sure they are not bent or damaged. 

 

Comments

Visitor, September 9, 2017
Changed the battery on key fob, doors lock,trunk opens but car won't remote start Chrysler 200
Visitor, September 9, 2017
Hi, I have Town and Country 2012. I replaced the battery, the engine starts Ok but doors can not open with remote.
You Chrysler key has two different circuits. One that is powered by your car's igntion system by inducing a current. That is the system that starts the car and doesn't need the batteries to work. The second circuit is used to lock and unlock the car. It can fail. The car may still start. What you can do is go to a place that makes keys or even auto parts stores. They often have key battery tester that check the how strong the signal of the battery is. Test you key. If it doesn't send a signal you have a bad key. If the door lock unlcok works with your other key, then you have confirmed that the key is defective.

Related Guides

Popular Articles