Front Brake Pads and Rotor Replacement Hyundai Elantra

Front Brake Pad and Rotor Replacement Hyundai Elantra 2011-16

Last Updated on Friday May 18, 2018

This DIY guide shows you how to change front brake pads and rotor on Hyundai Elantra model years 2011-2016. Make sure you have replacement brake pads and rotor ready. The Wagner ThermoQuiet QC1544 ceramic Disc Pad are very good option. These brake pads fit Hyundai Elantra many owners seem to love them. It is up to you what brake pads you choose. When it comes to rotors make sure you install vented brake rotors. This may be the time to upgrade to slotted and drilled Hyundai Elantra rotors

Torque Specifications

  • 14 mm Caliper guide bolts 20 lb-ft. 
  • Brake Caliper Retainer / Bracket 70 lb-ft


Step 1: Engage Parking brakes learn how to change hyundai elantra brake pads and rotors


Engage the parking brakes and ensure the gear shifter is placed in Park.

Step 2: Brake Fluid Reservoirhow much does it cost to change hyundai elantra brake pads yourself

Start by opening the hood and removing the brake fluid reservoir cap. This is necessary and will make it possible for you to press the caliper pistons in. You will need to do this in order to fit the new thicker brake pads in the brake caliper. 

Step 3: Loosen Lug Nuts

Before you raise up the car make sure to break loose the lug nuts. Do not remove them yet, just loosen them a turn or so.  

Step 4: Raise Vehiclediy brake pad replacement hyundai elantra

Use a floor jack to raise up one of the front wheels. Carefully raise the front of your car with a jack and then support the car with jack stands

Remove tire. Remove lug nuts and keep them in a safe place so you don't lose them.

Step 5: Remove Caliper Boltscan I change my hyundai elantra brake pads myself

Locate the two bolts on the back of the front brake caliper. Remove both bolts. Use a 17mm socket and a ratcheting wrench to loosen the lower and upper caliper bolts on the back of the caliper and pull each bolt slightly out. You need to slide them out to allow room to remove the caliper.

Secure the brake caliper.
Use a wire to secure the brake caliper. Do not let the brake caliper hang as this can cause damage to the brake hose. Lift the caliper off the brake pads and tie it with a rope to the strut to keep it from falling and void putting tension on the brake line.

Step 6: Remove Brake Padsdiy hyundai elantra brake pad replacement

Once you remove the two bolts you will be able to pull out the caliper and remove the brake pads. Loosen the two rotor retaining bolts using a Phillips screwdriver. These bolts can be difficult to come out and may require that you use a Hand Impact Tool Set.

Step 7: Remove Brake Pad Bracket

Before you can remove the rotor you need to remove the brake pad / caliper bracket / caliper carrier. It is held in place with two bolts. These are 17mm bolts. Remove the bolts using a breaker bar.

Step 8: Remove rotorhyundai elantra front brake pad replacement guide

Removing the old rotor can be tricky. Remove the screw that holds the rotor secure. Next, you need to remove the rotor. Try wiggling the rotor back and forth. If the rotor does not come loose you may have to use a hammer to get it off. Spray penetrating oil such as WD-40 and let it sit for 10 minutes before you try to remove the rotor.

Step 9: Clean Areahow to change front rotor and brakes hyundai elantra

It is time to install the new rotor. We recommend that you clean the hub area with a steel wire brush before you install the new rotor. Compare the old and the new rotors to make sure they are the same size then fit the new rotor carefully. If you are installing new slotted rotors, make sure they are fitted correctly so that they would spin in the proper direction.

Install new rotor. Slide the new rotor in place. Tighten the rotor retaining bolts.

Step 10: Caliper Bracket diy hyundai elantra brake pad changing guide

Next install the bracket and tighten the two bolts on the back. Remember the bolts on the back of the brake pad bracket need to be tight. If you are using a torque wrench make sure to torque them at 70 ft-lbs.  

Clean. Using a dry towel or a rag, you can clean the dirt from the calipers and the pistons with a special spray for cleaning brake parts.

Step 11: Install new brake to change hyundai elantra brake pads

The new brake pads will probably be thicker than the older ones, you will need to use an even surface (e.g the old brake pad) to press back the caliper pistons so you would be able to fit the new brake pads inside the brake calipers. A C-clamp can be used to compress the pistons backward. Don't push the pistons too far, only until the pistons are in-line with the rubber dust boot. Put the new brake pads in its place, make sure they are tight and well-fitted. After fitting the new brake pads, you might experience light braking noise or squeaking; to eliminate that noise you can use CRC Disc Brake Quiet for brake pads.

Install new caliper. Loosen the caliper from the rope carefully and tighten the lower caliper bolt using a 17mm socket and ratcheting wrench. Use brake caliper grease to lubricate the caliper bolts. Install new caliper and tighten the two bolts.

Refit the front wheel and spin the lug nuts with your hand. Tighten the lug nuts in a criss-cross pattern. Lower the vehicle until it puts weight onto the wheel to prevent it from spinning then complete tightening the lug nuts.

Related Resources

  1. Hyundai Elantra Front Brake Pad and Rotor Replacement Shop Manual Instructions
  2. Hyundai Elantra Front Brake Pad Repair and Inspection Procedures