Nissan CVT Transmission Speed Sensor Replacement DIY
Transmission speed sensor on Nissan CVT automatic transmission may fail. It can cause problems such as hard shifting, check engine light on or a bang when you move the shifter from Park to Drive or Reverse gears. This transmission is installed on multiple cars including Nissan Altima, Cube, Juke, Maxima, Murano, NV Cargo, Pathfinder, and Quest.
Symptoms of bad transmission speed sensor
- Engine bangs when placed in Drive / Reverse
- Check Engine Light On
- P0720 Fault Code
- P0500 - Vehicle Speed Sensor
- Harsh shifting
- Cruise control stopped working
- Possibly Related Fault Codes
- P0703, P0705 Range Sensor,
- P0706, P0711, P0712, P0713, P0715,
- P0717 input speed sensor,
- P0730 incorrect gear ratio,
- P0740 torque converter,
- P0743, P0779, P776, P0746
Nissan Input Speed Sensor Location
On Nissan vehicles equipped with the CVT transmission, the input speed sensor is located on the side of the transmission housing.
Nissan Transmission Speed Sensor Replacement
What you need
- Nissan CVT Speed Sensor
- Car Ramps
- 10mm socket, extension, and ratchet.
- 1/4" socket and ratchet drive recommended.
- 4" Extension
- Flexible ratchet extension can make it easier to get to the 10mm bolt.
There are two methods to replace the speed sensor on Nissan CVT transmission. The first requires that you remove the battery and the starter which will take a lot of time. The second is to access the speed sensor from the bottom of the engine. You won't be able to see the sensor and will be accessing it blindly but the following pictures and video clips should help you with this task.
- Jack up the vehicle or drive it on on ramps. For safety reasons, we recommend using ramps. https://player.vimeo.com/video/222203577
- Remove the plastic splash shield from the bottom of the engine.
- Locate the transmission speed sensor.
- Disconnect the electrical connector. Use a flat screwdriver to pry the plug away from the sensor.
- Remove the 10mm bolt. Get it loose using your 10mm socket and ratchet. Next, remove the bolt by hand.
- Remove the old speed sensor from the transmission housing. There may a very small amount of oil leaking from the sensor hole.
- Reinstall the new sensor. Make sure it has the O-ring in place. Apply a little bit of oil on the O-ring before installation. It is not recommended to reuse the old O-ring.
- Tighten the 10mm bolt.
- Lower the vehicle and follow proper procedure to check the automatic transmission fluid level.
- The sensor is right below the starter. If you are accessing the sensor from underneath the vehicle, it is better to use 1/4" ratchet and 4" extension to get to the 10 mm bolt.
- Service manual instructions can be found here.
Transmission Speed Sensor Replacement Cost
Replacing the automatic transmission speed sensor on Nissan CVT transmission can cost anywhere from $450-$600. That's because it requires that you remove the battery and the starter to get to the sensor. Once you watch this tutorial you should be able to replace the sensor without having to remove the starter and the battery. Access the sensor from the bottom of the engine. You won't be able to see the sensor directly but keep watching this guide for help.
How to check Nissan transmission speed sensor
A mechanic will connect an OBD-2 scanner that can read Nissan transmission codes. Note that you need a multi-system OBD2 scanner and that generic OBD2 scanner is not able to retrieve all transmission fault codes. Read our guide on Choosing the best OBD2 scanner for DIY auto repair.
- Locate the OBD2 port under the dashboard.
- Turn the ignition to position II. All dash lights will turn on.
- Allow the scanner to power on.
- Select Automatic Transmission menu or A/T menu.
- Select read codes.
- Verify that there are fault codes pointing to a faulty transmission speed sensor.
Where to buy Nissan transmission speed sensor
Buy cheap Nissan transmission speed sensor online. Check the price on Nissan transmission speed sensor: