In this guide, you will find step-by-step instructions on how to change the clock spring on Hyundai vehicles.

The video clips and pictures are from a 2016 Hyundai Elantra but these instructions should help owners of other Hyundai models as well. 

What you will need

  • Flathead screwdriver
  • Metric Sockets
  • Ratchet
  • Work Gloves
  • Torque Wrench
  • 21mm socket
  • 10mm wrench

Procedrue

  1. Locate the battery in the engine bay and disconnect the negative cable. To remove the cable from the battery post you will need to loosen the 10 mm bolt.
  2. Wait at least 10 minutes before you start work on the airbag system.

  3. Remove the airbag by using a screwdriver to press on the three locking pins that hold the Hyundai Elantra airbag in place.

  4. Next, you will need to remove the 21 mm nut that holds the steering wheel in place. It is easier to remove this nut using a breaker bar.

  5. Once you remove the steering wheel you will be able to access the clock spring. Before you can remove the clock spring you will need to remove the plastic trim which is held in place with three screws.

  6. Install new clock spring in reverse order. Ensure all electrical connectors are secure. Tighten the steering column nut to 50 Nm using a torque wrench.

Photo Gallery

hyundai elantra airbag clock spring removal
how to replace clockspring on hyundai elantra
hyundai airbag steering wheel clcock spring remocal
clock spring replacement guide hyundai
hyundai how to replace clock spring yourself
diy cloock spring replacement
hyundai clock spring replacement cost
how to fix airbag light on hyundai
hyundai airbag light replacement problem
hyundai elantra airbag light on due to a bad clock spring
clock spring hyundai diy guide

Applications model years: 2011, 2012, 2013, 2014, 2015, 2016. Replacing the clock spring on a Hyundai Elantra is easy and requires about 2 hours.

We hope you found this guide helpful. Please consider showing your support for YOUCANIC by subscribing to our YouTube channel.

Thank you! 

Visitor
Member since 2020-07

Sorry bros but the technician in for step 4 "remove the clock spring" should consider pullong that video and repost with a different example ...based on that video i wouldnt let you work on my lawn tractor let alone a 30k car.i mean really ?

  •  
  •  
  •  
Visitor
Member since 2020-07

Well he is not working on your car is he? If that video isn't good than why don't you consider posting one yourself so that you can help others? I think the guy is removing the clock spring on that car for the first time. Learn from his mistakes I guess.

  •  
  •  
  •  
Visitor
Member since 2020-07

Spot on DIY. Replaced the Clockspring in my 11 Elantra. Everything went like clockwork, pardon the pun. apart and back together in less than 45 minutes. All working now. Lights OFF. horn Works, Steering Wheel buttons all working again, Much Gratitude! The video's were a lifesaver while I was doing all the steps. Bravo! -From Central Texas

  •  
  •  
  •  
Visitor
Member since 2020-07

Great article! Here is a tip for those trying this for the first time. If you trigger the airbag light you may need to use a tool such as Hyundai's GDS or Autel MaxiDAS to re-establish the steering angle sensor set point after repair.

  •  
  •  
  •  
Visitor
Member since 2020-07

I scanned the car, went to the SRS Airbag / ABS menu, read the code. Replaced the airbag clock spring, reread the codes. Old code was still there - high voltage on driver's airbag. Cleared the code, drove the car around and so far so good.

  •  
  •  
  •