How to Replace Outer Tie Rod on a BMW

Vehicle:   BMW
Difficulty: ⚫⚫⚪⚪⚪
DIY Cost: $60-$200
Est. Time: 1-2 hours

In this guide, you will find instructions on how to replace out tie rods on BMW vehicles. Replacing a BMW out tie rod is very easy and can be completed in about two hours.

Symptoms

Here are a few symptoms that you may notice when you have worn tie rods. 

  • Uneven Tire wear - One of the most common symptoms of worn tire rods is uneven tire wear. Typically the inside or the outside of the tire will wear much faster than the rest of the tire. 
  • The steering feels loose - Another common sign that your tire rods need to be replaced is loose steering feel. 
  • Unstable at high speed - If you feel that it is difficult to keep your car in the lane or that the car shifts a lot on uneven lanes, the problem could be the tie rods. 
Missing taxonomy term.

What you will need

A list of tools and parts that you will need.

Missing taxonomy term.Missing taxonomy term.

Procedure

  1. Loosen the front lug nuts using a 17mm deep socket. Don't remove the wheel yet, just break the lug nuts loose. This should be done while the car is on the ground.

  2. Next, jack up your BMW and support it with jack stands. Remove the wheel. Do not rely on the car jack alone. Use jack stands to support and secure the vehicle. Place wheel chocks behind the rear tires to prevent your vehicle from rolling back.

  3. Locate the out tie rod. On BMWs (and most cars) the outer tie rod is behind the steering knuckle.
  4. When possible spray penetrating oil on the castle nut to make the reveal easier.bmw outer tie rod location
  5. Loosen lock nut. Use a wrench to loosen the pinch nut. Some BMW models use a pinch bolt instead of a nut. Use a T-50 bit to loosen the bolt where the outer tie rod and inner tie rod connect. bmw outer tie rod lock nut
  6. Remove the cotter pin. This prevents the outer tie rod nut from getting loose while driving. Use a pair of pliers to straighten the pin and pull it out. Some BMW use a washer with tabs that are folded inwards.
  7. Fold the tabs out with needle nose plier in order to remove the castle nut. bmw uses lock washer instead of cotter pin
  8. Remove the castle nut using an 18mm open-end wrench. In some cases, the bolt may start to spin freely.
  9. You will need to use an Allen wrench or an 8mm wrench to hold the center of the spinning bolt in place.
  10. remove bmw tie rod castle nut
  11. Remove BMW outer tie rod from the steering knuckle.  Use an outer tie rod puller to separate your BMW tie rod from the steering knuckle. If you don't have an outer tie rod puller, use a ball joint fork.remove tie rod bmw steering knuckle

  12. Even though you will need to perform front end alignment, you should aim to keep the alignment as close to the original as possible. To do this, measure the distance from the castle nut to the pinch nut. It may help to use a marker and mark the threads on the inner tie rod where the outer tie rod meets.

  13. Unscrew outer tie rod from the inner tie rod. 

  14. Once you are done disconnecting the outer tie rod from the steering knuckle, the next step is to completely remove it from the car.To do so, twist your BMW outer tie rod counter clockwise.
  15. Install the new tie rod in reverse order. First, thread it on the inner tie rod. Next, tighten the castle nut.

  16. Install the pinch bolt or tighten the pinch nut. Install the cotter pin. If your BMW doesn't have a cotter pin, it should have the washer with tabs.
  17. Bend the tabs inwards towards the nut. install bmw tie rod
  18. Torque the castle nut to 50 ft. lbs. Torque lock nut to 35 ft. lbs. Verify these values by calling your BMW dealer and providing the VIN of your car.torque bmw tie rod

  19. Install the wheel. Lower the vehicle and torque the lug nuts. On most BMWs, 90 ft-lb is the recommended torque for the lug nuts.
  20. Get your front wheels aligned

Congratulations!

You have replaced BMW tie rods. You may notice that the steering wheel is not on center or that your BMW pull to the left or right. You will need to take your BMW for a front wheel alignment.

With new BMW tie rods installed, you will notice that the car will handle much better and the steering is more responsive. Your BMW will feel and drive like a new car again. If you have any questions or tips please use the comment section below.

Why should I get wheel aligment? 

car front wheel alignment shop

When you replace the BMW tie rod ends, you throw wheel toe out of alignment. Your BMW dealer can do this or any wheel alignment shop.

 

 

BMW uses the same tie rod design among many models.

 

This DIY guide will help owners on BMW 1-series, 3-series, 5-series, 6-series, 7-series, X1, X3, X5, X6, Z3, Z4.

 

Notes

 

  •     Replace Bad Tie Rods ASAP - Do not ignore a bad tie rod. If the tie rod fails while driving, you will lose steering and most likely end up in an accident. 
  •     Replace Both - It is recommended to replace both out tie rods at the same time. 
  •     Front Wheel Alignment - Front wheel alignment is required after changing out tie rods. 
  •     Verify your Tie Rods are Bad - You can check if the tie rods are bad by jacking up the car. Grab the wheel at 3 and 9 o'clock and try to rock it in and out. There should be no play. If there is, it indicated that the tie rods are the culprit. 
  •     Check inner tie rods as well - Some cars have inner tie rods and outer tie rods. A bad inner tie rod will exhibit similar symptoms as a bad outer tie rod. 

Replacement Cost

The cost to change BMW tie rods at the dealer or mechanic ranges between $400-$600.

If you decide the change your BMW tie rods yourself, expect to pay anywhere from $30 to $100 for a set of new tie rods. You will spend an additional $100 to get the front wheels aligned.

By YOUCANIC Automotive Experts
Jun 2020