How to replace front strut and spring or upgrade springs on Tesla Model 3. These pictures and videos are based on a 2018 Tesla 3 AWD. The same procedure can be followed for RWD models. See note in the DIY guide. 

In this guide, you will find instructions on how to replace the front struts on the first generation Tesla Model 3. 

You can use this guide to replace your worn front struts or upgrade the suspension springs. 

What you will need

Procedure

  1. Park your Tesla on level ground. Tesla diy projects

     

  2. Loosen the lug nuts but do not remove them yet or the wheel. break loose tesla lug nuts

     

  3. Insert the jack pad in the hole used to jack up the vehicle. Using the jack pad adapter will prevent damage to the battery pack. tesla jack pad
  4. Raise the vehicle and secure it with jack stands in addition to the jack.  Do not rely just on the jack. jack up teslaJack stands should only be placed to support the frame. Do not place a jack stand under the battery. 
  5. Open the hood of the vehicle by pressing OPEN on the touchpad.  open tesla hood
  6. Remove the plastic covers in the front by lifting it. This piece does not have any screws. remove tesla engine plastic coverThe center plastic pops up. 
  7. Remove the air inlet vent.  White plastic clips pop up. inlet plastic vent
  8. Next, remove the 10mm bolts and remove the larger plastic cover. Two bolts are at the back. tesla plastic trunk removalTwo more bolts are by the hood latch. Tesla bolts near hood latch
  9. Once all the bolts are removed, lift the plastic cover. remove tesla frunk plastic Note that you will need to disconnect the wire for the light. 
  10. Raise the vehicle. Secure it with jack stands in addition to the jack. Remove the wheel. tesla model 3 front wheel removed
  11. Use an 18mm socket to remove the nut for the sway bar link. sway bar linkIf the nut and bolt start to spin, use a T30 tox bit to hold the center of the bolt while you remove the nut with an open-end wrench. hold tesla sway bar link bolt
  12. Use a 21mm socket and wrench to remove the bolt that secures the strut to the lower control arm. Tesla front strut replacement upgrade bolt
  13. Use a 13 mm socket to remove the three bolts from the strut. If your 13mm socket does not fit in this hole, you may be able to use a standard 1/2" socket. The other option (not recommended) is to use a large drill bit to enlarge the hole. Getting to these bolts is tricky and requires patience. strut top bolt tesla model 3
  14. Unhook the ABS wire from the steering knuckle. ABS wire removed
  15. All-wheel models only -  Remove the nut and bolt that secures the steering knuckle to the upper control arm. This step is not necessary for rear-wheel-drive models. Tesla MOdel 3 awd front strut and coil spring replacement
  16. Remove the strut from the vehicle. Two people are needed for this step. The upper control arm will need to be pushed up. The lower control arm will need to be pushed down. 
  17. Place the spring compressors on opposite ends of the spring. remove spring on tesla model 3 front shock strut
  18. Tighten each spring compressor a few threads at a time. Do not compressor only one spring compressor all the way, then move to the other side. Tighten both spring compressors by alternating between the two. 
  19. Once the spring compressor has compressed the spring significantly, you should notice the strut mount getting loose. Remove the rubber cover at the center of the strut mount. Use a deep socket to remove the nut at the center of the strut mount. 
  20. Remove the strut mount by sliding it out of the spring. Swap the strut or install the upgrade springs/lowering springs. 
  21. Install in reverse order. Check the strut nut once the vehicle is lowered to the ground. how to upgrade install tesla model 3 coil overs

Replacing the front struts on a Tesla Model 3 is relatively easy and very similar to replacing the same component on many European vehicles such as BMW and Mercedes-Benz. 

Tips

  • Make sure the rubber pieces for the springs are seated properly. They should be rotated to match the spring. 
  • Pay attention to the alignment of the strut support bolts to the strut. The bolts need to be installed in the same position, or the strut bolts will not line up with the bolts holes in the strut. 
  • You will need two people when you remove the strut from the car—one to push down on the lower control arm and push up the upper control arm. The second person will be removing the strut/spring assembly from the vehicle. 
  • On AWD models, you need to separate the steering knuckle from the upper control arm. On RWD models, you do not need to separate the upper control arm. 
  • On AWD, it is recommended to replace the bolt secures the steering knuckle to the upper control arm ball joint. 

Torque Specifications

  • Three nuts at the top that secures strut to frame: 20 ft-lb / 25Nm
  • Sway bar end links 73 ft-lb / 98Nm
  • Strut to lower control arm: 100 ft/lbs
  • Lug Nut Torque Spec: 130 ft/lbs
  • Bolt/nut combination for clamp-on knuckle / upper control arm ball joint - 41 ft-lb / 56Nm

These are the estimated values only. 

It takes about two hours to replace a front strut or upgrade one spring on a Tesla Model 3. To replace both front struts on a Tesla Model 3, it takes between three to four hours. 

We hope you found this guide helpful. Please consider showing your support for YOUCANIC by subscribing to our YouTube channel.

Thank you!