VW Combination Switch Replacement

Vehicle:   Volkswagen
Difficulty: ⚫⚫⚪⚪⚪
DIY Cost: $80-$200
Est. Time: 1-2 hr

If your VW turn signals don't work or turn signal don't cancel or high beams don't work or wiper doesn't work or cruise control doesn't work, there is a good chance the combination switch is the problem.

In this guide, you will learn how to replace the turn signal switch and wiper switch on a Volkswagen vehicle, known as the combination switch.  

On most Volkswagen vehicle turn signal and wiper switch are integrated into one unit and have to be replaced as one. The pictures and videos shown here are from a Volkswagen Jetta MK6, but the procedure is almost identical for VW Bora, Golf, Passat, Polo, CC, EOS, Tiguan, Routan, etc. 

Symptoms

Here are a few symptoms that can be caused by a faulty VW combination switch. 

  • Turn signal switch doesn't work
  • Turn signals don't cancel
  • High beams don't work 
  • Cruise control doesn't work 
  • Windshield wiper switch doesn't work

What you will need

Instruction

How to change a Volkswagen combination switch: 

  1. Turn on the ignition and turn the front wheels so that they are pointing forward. VW Wheel
  2. While the ignition is on, open the hood, locate the battery and disconnect the negative battery terminal. This will ensure the steering wheel remains unlocked and can be turned.  Remove the key for the ignition/vehicle. Wait at least 15 minutes before proceeding to the next step. Disconnect the battery
  3. Lift up the upper trim that is after the steering wheel. It most models, the trim has just clips and no screws. VW airbag remvoal

     

  4. Turn the steering wheel to the left to bring the side of it to the top. 
  5. Use a flat screwdriver to push through the back of the steering wheel and release the airbag. On newer VW vehicles, there is no visible hole behind the steering wheel. There are two indents that you need to punch through with the screwdriver. vw airbag removal hole

     

  6. Turn the steering wheel and release the airbag on the other side. Hold the airbag so that it does not fall. Releasing the airbag requires patience. If you need help with this step see our guide on how to remove a VW airbag.Removed VW airbag

     

  7. Pull out the airbag and disconnect the electrical connector on the back. Handle the airbag with care, and keep your body at least one foot away from the airbag at all times. 
  8. Remove the bolt at the center of the steering wheel using an M12 Tripple Square Bit. Have a friend counter hold the steering wheel while you break loose the bolt. VW Steering Wheel Screw
  9. Mark the steering column shaft and steering wheel so that the steering wheel is installed in the same location.Mark steering wheel
  10. Remove the steering wheel. Remove vw steering wheel

     

  11. Remove the lower steering column trim. It is held in place with three screws. Two screws are next to the clock spring. One screw is below the steering column. Remove VW steering column trim

     

  12. Remove the screws that hold the clock spring in place. Disconnect the electrical connectors and remove the clock spring.vw clock spring removal For more help see this guide on How to Replace VW Clock Spring
  13. Remove the Torx screw at the bottom of the combination switch.Remove vw combination swtich turn signal switch crusie control wiper switch

     

  14. Unplug the electrical connectors from the combination switch. The electrical plugs have red tabs that need to be released first.VW combination switch  connector
  15. Pull out the combination switch.VW Turn Signal Wiper Switch 
  16. Install the new one in reverse order. VW combination switch location
  17. Torque the steering wheel bolt to 50 Nm. 

ABS or traction control light may be on when you first start the engine, but they will reset automatically after you drive for a few minutes. 

Replacing the combination switch on a Volkswagen is easy and takes less than two hours. You need to be extremely careful handling the airbag. The airbag can deploy and cause injuries or damage. 

The average cost to replace a Volkswagen turn signal switch, wiper switch, (combination switch) ranges between $350 and $600. While the cost to replace a VW combination switch yourself ranges between $80 and $200 if you have the tools. 

 

By YOUCANIC Automotive Experts
Nov 2020
VW Combination Switch Replacement If your VW turn signals don't work or turn signal don't cancel or high beams don't work or wiper doesn't work or cruise control doesn't work, there is a good chance the combination switch is the problem. In this guide, you will learn how to replace the turn signal switch and wiper switch on a Volkswagen vehicle, known as the combination switch.