Floor jacks are essential components if you do your car repair! Not only can they make your job easy, but they also are critical when it comes to completing the repair safely! Whether you need to replace your tires or change your brake pads, a garage floor jack is a must. In this article, we have highlighted some of the features you need to consider when choosing the best car jack. Manufacturers promote all kinds of features to sell their jacks, but we wanted to highlight those that are most critical when choosing the right floor jack.
Most floor jacks have a range between 5 to 14 inch. There are a few floor jacks that provide better range. Here are some floor jacks that can go lower and lift higher too.
3 Ton Capacity.
Lift Range: 5.12" to 20.1"
Things to consider when buying a floor jack.
Given that there are so many floor jacks to choose, it is not an easy task to decide on what to buy. If you go to Harbor Freight, Advance Auto Parts, Auto Zone, Costco or even Home Depot you typically see multiple floor jack on sale. Here are some factors will help you choose the best floor jack:
When selecting a floor jack consider these features.
Having a poorly designed floor jack could be hazardous. Imagine if it collapses immediately after you lift up the vehicle. What amount of damage could it cause, especially if there was anyone beneath the car? It is, therefore, important to have adequate and correct information about them, before you invest in one.
The floor jack will lift heavy loads and therefore its stability and strength is a point of consideration. Aluminum and steel are the two most critical materials that make the floor jacks. Both of them are strong enough, but their durability and stability under different conditions are of concern. Steel floor jacks are heavy, therefore have reduced portability as compared to aluminum. While steel floor jacks tend to be heavier their main benefit is that they are more durable than aluminum jacks. Aluminum floor jacks are much lighter and portable. They may not be as durable as a steel floor jack in the long run. If you need a jack for your garage, it makes more sense to go for an aluminum floor jack. Some floor jacks such as the Powerzone 3 Ton Aluminum and Steel Garage Jack provides the weight reduction feature of an aluminum jack but uses steel at critical points to provide the best durability and weight combination.
This is quite important to avoid purchasing a limited floor jack. The only trick in this is investing in a jack that can lift weight close to the entire vehicle?s weight. With such a lifting capacity, you will always be sure of safety while lifting your car. Mechanical jacks will lift up to a maximum of 20 tons, after some effort of course. To determine the weight of your car look at the sticker that shows the weight typically in pounds. Rember that 1 Ton = 2000 lbs. Keep in mind that you will only be lifting part of this weight as you will not be lifting the whole car up.
A two-ton floor jack will be all that most car owners need but if you frequently work on trucks and SUVs pick a floor jack with at least 3-ton capacity. Some floor jacks go to 4 ton and higher lift, but there is no need to go higher than 3-ton unless you know you are going to work on very heavy vehicles, RVs or buses.
This depends on the height required that depends on the profile of the car. For instance, some cars have a low profile that may require a floor jack that will fit in the small space and can lift the car to desirable heights. All these information should be in the product description of the floor jack, and they should match to your needs. If you are looking for a floor jacks to use on multiple cars, you should consider a floor jack that will work on low profile cars yet be able to lift a truck that requires a higher lift.
Most floor jacks fit in the middle of the range as they target the typical Camry and Accord sedans which are neither too low nor too high. That's why if you also own a sports car or an SUV you may need to choose carefully.
The most common form is a floor jack. It is the most practical type of jack for DIY auto repair and great for use as a garage jack. This buyer's guide is focused on garage floor jacks, but there are a few other options that you may want to consider depending on your need. It is the most popular jack type due to efficiency and user friendliness. With this one, you will only have to pull the plunger, and the jack will start pumping upwards. It uses hydraulic fluid (oil) to create pressure that lifts up the jack?s arm. Some floor jacks have a stopper to prevent it from falling off after it reaches the maximum lifting height.
Scissor-type floor jack
Its name comes from its scissor-like action, while at work. It is a manual type of floor jack with a rotating handle and a crank, which is inserted in the vehicles slots. Its mode of action is simple; you rotate the handle shaft to provide the power.
This power pulls the outer sides to the middle section through the jack?s main screw. This action leads to a lifting of one side of the car. Due to its small size, it is a favorite for many responsible car owners. However, they will require a lot of energy to pump up the jack, which might not be suitable for many.
If your car jack is missing and you need a jack to replace it, a scissor type jack will get the job done when you need to replace a flat tire. An excellent choice to replace your car's jack is the Torin T10152 Scissor Jack.
Piston floor jack
Due to its ?standing up? orientation, it is also known as Bottle floor jacks. It uses hydraulic fluid but at higher pressures which lead to higher lift heights. They are suitable for industrial uses and can also be used vehicles. The bottle jacks typically have higher lift capacities. Their main advantage: they can lift at up to 50 tons worth of load. However, they may require additional support to promote stability, especially when lifting very heavy weights.
Hydraulic trolley jacks
The main advantage of these types of jacks is that they are portable. Also, they have higher efficiencies and speeds of lifting. With less than five strokes, the jack is already up. Due to the four wheels, it enjoys higher stability, which is important when lifting heavy loads. The amplified levers that it has increased the range of height that the jack can lift. It is unsuitable for small cars due to its heavy weight and area of action.
Durability and reliability of a jack is crucial, given the important role that it serves. There are many brands of floor jacks with different prices. Sometimes, the price will not define the quality of the floor jack, and it is important to read the customer reviews and do enough research. This is especially important for hydraulic jacks to avoid expensive maintenance.
Replacing a tire is always an emergency, and this makes the floor jack?s speed important. The average number of strokes that you will require to lift up the car defines the speed. The maximum strokes for a jack should not exceed 10. Although it is expensive, well-designed jacks may take less than five strokes to reach maximum lift range.
Choosing the best jack for your garage depends on your needs and requirements. Here are some of the most popular floor jacks depending on specific uses:
Low Profile Jack: Pro-Lift F-767 Grey Low Profile Floor Jack
Aluminum Jack: Arcan ALJ3T Aluminum Floor Jack - 3 Ton Capacity
Car and Motorcycle Jack: Powerbuilt 620422E Heavy Duty 4000 Lb Triple Lift Jack
BEST OVERALL CAR JACK:
Which is the best floor jack after all? That depends on your needs. It is important to choose a floor jack with a reasonably higher lifting capacity that your car to be on the safe side. Keep in mind that because you are lifting the car on one side even a lower capacity floor jack will be able to raise the car since some of the weight is typically on the wheels resting on the ground and the rest of the weight will be on the jack. We would recommend a floor jack with a high capacity, close to or higher than the gross vehicle weight rating (GVWR), or gross vehicle mass (GVM). You should never depend just on the floor jack when working on your car or truck.
In case you need a floor jack to suit different weights of cars you should pay attention to the lift range of the floor jack Will it work on a low profile car, yet be able to raise a truck. Also, consider how quickly the jack lowers! This may not seem like an important factor, but you don?t want to drop your vehicle to the floor like it is apple in freefall. Even some of best overall jacks drop the car too quickly! Don?t assume that every floor jack will lift any weight to any height.