Skip to main content
This guide provides instructions on how to change front brake pads and rotors on a Hyundai vehicle.

Table of Contents

The videos and pictures are from a 2015 Hyundai Elantra. These instructions should still help you replace the brake pads on other Hyundai models such as Accent, Santa Fe, Sonata, Tucson, etc. 

What you will need


How to change front brake pads and rotors on a Hyundai. 

  1. Set the parking brakes and place the transmission in Park. learn how to change hyundai elantra brake pads and rotors

  2. Open Brake Fluid Reservoir. Start by opening the hood and remove the brake fluid reservoir cap. This is necessary and will make it possible for you to press the caliper pistons in. You will need to do this to fit the new thicker brake pads in the brake caliper. how much does it cost to change hyundai elantra brake pads yourself

  3. Loosen Lug Nuts. Before you raise the car, make sure to break loose the lug nuts. Please do not remove them yet; loosen them. 

    loosen lug nuts
  4. Raise Vehicle. Use a floor jack to raise one of the front wheels. Carefully raise the front of your car with a jack and then support the car with jack stands. 

    raise vehicle
  5. Remove tire. Remove lug nuts and keep them in a safe place so you don't lose them. A secure vehicle with jack stands. Always secure the vehicle with jack stands. Don't rely on the jack vehicle
  6. Remove Brake Caliper Bolts Locate the two bolts on the back of the front brake caliper. Remove both bolts. Use a 14mm socket and a ratcheting wrench to loosen the lower and upper caliper bolts on the caliper's back and pull each bolt slightly out. You need to slide them out to allow room to remove the caliper. Secure the caliper. Use a wire to secure the brake caliper. Do not let the brake caliper hang as this can cause damage to the brake hose. can I change my hyundai elantra brake pads myselfLift the caliper off the brake pads and tie it with a rope to the strut to keep it from falling and void, putting tension on the brake line.

  7. Remove Brake Pads Once you remove the two bolts, you will pull out the caliper and remove the brake pads. Loosen the two rotor retaining bolts using a Phillips screwdriver. These bolts can be difficult to come out of and require that you use a Hand Impact Tool hyundai elantra brake pad replacement

  8. Remove Caliper Bracket Before you can remove the rotor, you need to remove the caliper bracket carrier. It is held in place with two bolts. These are 17mm bolts. Remove the bolts using a breaker bar.

  9. Remove rotor Removing the old rotor can be tricky. Remove the screw that holds the rotor secure. Next, you need to remove the rotor. Try wiggling the rotor back and forth. If the rotor does not come loose, you may have to use a hammer to get it off. Spray penetrating oil and let it sit for 10 minutes before you try to remove the rotor. diy hyundai elantra brake pad changing guide

  10. Clean It is time to install the new rotor. We recommend that you clean the bracket with a steel wire brush before you install the new pads.

  11. Compare the old and the new rotors to make sure they are the same size, then fit the new rotor carefully. If you are installing new slotted rotors, make sure they are fitted correctly to spin in the proper direction.
  12. Install the new rotor. Slide the new rotor in place. Tighten the rotor retaining bolts.
  13. Next, install the bracket and tighten the two bolts on the back. Remember, the bolts on the back of the brake pad bracket need to be tight.
  14. If you are using a torque wrench, make sure to torque them at 70 ft-lbs.
  15. Clean. Using a dry towel or a rag, you can clean the dirt from the calipers and the pistons with a special spray for cleaning brake parts.
  16. The new brake pads will probably be thicker than the older ones; you will need to use an even surface (e.g., the old brake pad) to press back the caliper pistons so you would be able to fit the new brake pads inside the brake calipers.
  17. A C-clamp can be used to compress the pistons backward. Don't push the pistons too far, only until the pistons are in line with the rubber dust boot. Put the new brake pads in their place; make sure they are tight and well-fitted.
  18. Refit the front wheel. Tighten the lug nuts in a criss-cross pattern. Lower the vehicle until it puts weight onto the wheel to prevent it from spinning, then complete tightening the lug nuts to specification. 

Torque Specifications

  • 14 mm caliper guide bolts: 20 lb-ft.
  • Brake Caliper Retainer / Bracket: 70 lb-ft
  • Lugnut bolts: 85 ft-lb
Hyundai Front Brake Pads & Rotor Replacement This guide provides instructions on how to change front brake pads and rotors on a Hyundai vehicle.