2011-17 Dodge Durango spark plug replacement 3.6l V6 Ignition coil

In this tutorial, we will focus on 2011-2017 Dodge Durango spark plug replacement. This DIY guide applies to Dodge Durango equipped with the 3.6L V6 Pentastar engine. Follow this guide if you need help with replacing the spark plugs as well. 


diy dodge durango 3.6 v6 spark plug ignition coil replacementSpark plugs may wear out on Dodge Durango due to high mileage and cause poor engine performance and engine misfire. Old spark plugs can cause the engine to turn on the check engine light or cause the CEL to flash. 

Why is this important!

It is important to change the spark plugs on your Dodge Durango at the recommended 100,000-mile mark to avoid engine problems. Old spark plugs may cause poor fuel economy as well. Engine misfire are one common sign of old spark plugs. 

Dodge Durango Spark Plug Replacement Cost

It costs between $280-$400 to replace the spark plugs on a 2011-2017 Dodge Durango. The reason why it is more expensive than most cars is because the intake plenum which sits on top of the engine needs to be replaced. This requires one to two hours extra work and that's why shops are going to charge you more to replace the spark plugs on a 3.6 Dodge Durango with the Pentastar engine. You can possibly change the spark plugs yourself and save $205-$300. 

Dealer Auto Mechanic DIY
$280-$400 $200-$350 $50-$90

Dodge Durango Spark Plug Replacement Interval

how to change spark plugs on dodge durangoBased on the owner's manual the spark plugs on the 3.6l V6 Pentastar engine should be changed every 100,000 miles. Only use platinum or iridum spark plugs. If you decide to install copper spark plugs, they need to be replaced every 30,000 miles. 

11-17 Dodge Durango Spark Plug Replacement


Ignition Coil and Spark Plug Replacement 3.6l Pentastar Engine

Parts Required

  • Spark Plugs
    There are many options when it comes to the spark plugs but here are the Top 3 you should consider. Note that these spark plugs come pre-gapped and should not be changed. The required gap is 0.043". Spark plug tightening torque is 13 lb/ft. 
  • Ignition Coils
    • Mopar 5149168AI
      • OEM ignition coil for Chrysler 3.6L Pentastar engine. It is recommended to stay with original factory coils to avoid problems down the road. Interchange part number: UF648, C1791, 5C1848, E1148, 2505484816, Supersedes 5149168AH.

Tools you will need

This is a list of tools that you will need to change the spark plugs and ignition coils on a 3.6L Pentastar engine. We hope you already have most of these tools. If you don't, we recommend that you invest in a mechanic tool set that has all these tools. 

  1. Allow the engine to cool down. Open the hood. 
  2. Disconnect the negative battery terminal. 
  3. Remove engine cover by pulling it up. You don't need to remove any screws to remove the engine cover. 
  4. Disconnect the vacuum lines. 
  5. Disconnect the air intake from the throttle body. Disconnect any vacuum tubes connected to the air intake tube. Loosen the 8 mm hose clamp screw. Unplug the air temperature sensor near the throttle body. 
  6. Remove the 8mm bolts (in some engine these may require T30 Torx bit) that secure the intake plenum (manifold) to the top of the engine. There are seven bolts that need to be removed.  These are long bolts and don't need to come all the way out. Remove the two 10 mm bolts on the front. Remove the two 10 mm bolts on the back of the intake manifold.how to replace spark plugs chrysler penta star Remove one 13 mm bolt on the metal bracket and push the bracket back. Next, lift up the intake manifold and move it aside. Cover the intake with a clean newspaper so that no foreign object or dirt falls inside the engine. 2012–2015 Lancia Voyager (Models: Limited)
  7. Rubber Gaskets between the plenum and intake manifold. 
    When you remove the intake plenum you will notice that there are three rubber gaskets between the plenum and intake manifold. These gaskets are typically integrated into the intake manifold part and don't necessarily need to be removed. Do not add any silicone or gasket sealant here as it is not necessary. The most important thing to do is tighten the intake plenum bolts to spec as described in the following steps.  2012–2014 Lancia Thema
  8. Remove the 10 mm bolts that hold the ignition coils in place. 2012–present Jeep Wrangler (Models: Sport, Unlimited Sport, Sport Unplug the electrical connectors from the ignition coils.  2011–2014 Volkswagen Routan (Models: S, SE, SEL, SEL Premium)Ignition coil removed.  2011–present Jeep Grand Cherokee (Models: Laredo
  9. Remove the old spark plugs. 2011–2016 Chrysler Town & Country (Models: LX, Touring, Touring There are six plugs.  2011–present Chrysler 300 (Models: 300 Base, 300 S V6, 300 C w/ V6, 300 C Glacier Series w/ V6, 300 C Luxury Series w/ V6)Spark plug removed.  2011–present Dodge Durango (Models: Express, SXT, Crew, Crew Lux, Citadel, ACT Plus, Limited, R/T)
  10. Be careful so that NO foreign materials fall into the combustion chamber via the spark plug holes.  Install the new spark plug by lowering them slowly. Note that all spark plugs that are iridium or platinum spark plug should come pre-gapped. You should always double check them and make sure they are all gaped correctly before inserting them into the cylinder head. Use the extension and your 5/8" socket to tighten the new spark plugs. Tighten the spark plugs to 10 ft-lbs. If you are not using a torque wrench you may want to get your spark plugs snug then turn an extra half a turn.  2012–present Fiat Freemont
  11. Add a coat of dielectric grease to the end of coil pack boot. 2011–present Dodge Charger (Models: SE, SXT, SXT +, SXT Rallye Edition)Insert the coil into the spark plug hole. 2011–present Dodge Journey (Models: SE American Value Package (AVP) or Canadian Value Package (CVP), Mainstreet, Crew, Crew Lux, SXT, R/T Crossroad)Tighten the 10 mm bolt until they are snug, don't over tighten these bolts.  2011–2015 Dodge Grand Caravan (Models: SE American Value Package (AVP) or Canadian Value Package (CVP), SE, Crew, Crew Lux, SXT, R/T SE Plus, SXT Plus)
  12. Install the plenum. If you have new gaskets to install between the intake manifold and plenum now is the time to replace them. Otherwise, go to next step. 
  13. Install the plenum in reverse order of removal. The 7 bolts will need to be torqued to 7-9 Nm (5-6.6 lb/ft). It is important that these bolts are torqued to spec. 
  14. Next, tighten the two 10mm bolts in front of the plenum. 
  15. Next, install the bracket on the other side of the plenum. Place the bracket in place and tighten the 10mm and 13mm bolts. 
  16. Next, reattach the air intake tube to the throttle body. 
  17. Reconnect any vacuum hose you disconnected earlier such as PCV hose and makeup line. 
  18. Reconnect wiring harness that you may have removed.
  19. Reinstall the engine cover by placing it on top of the engine and pressing it down until you hear it lock. 
  20. Reconnect the negative engine terminal. 
  21. Start up the engine and make sure the engine is running smooth. 
Vehicle Applications

This 3.6L Chrysler engine is found in the following makes and models and the instructions found on this page will help owners of:

  • 2011–2016 Chrysler 200 (Models: LX, Touring, Limited, S, and C)
  • 2011–present Chrysler 300 (Models: 300 Base, 300 S V6, 300 C w/ V6, 300 C Glacier Series w/ V6, 300 C Luxury Series w/ V6)
  • 2011–2016 Chrysler Town & Country (Models: LX, Touring, Touring "L", Limited, S, Limited Platinum)
  • 2011–2014 Dodge Avenger (Models: SE V6, SXT, R/T)
  • 2011–present Dodge Challenger (Models: SE, SXT, SXT +, SXT Rallye Edition)
  • 2011–present Dodge Charger (Models: SE, SXT, SXT +, SXT Rallye Edition)
  • 2011–present Dodge Durango (Models: Express, SXT, Crew, Crew Lux, Citadel, ACT Plus, Limited, R/T)
  • 2011–2015 Dodge Grand Caravan (Models: SE American Value Package (AVP) or Canadian Value Package (CVP), SE, Crew, Crew Lux, SXT, R/T SE Plus, SXT Plus)
  • 2011–present Dodge Journey (Models: SE American Value Package (AVP) or Canadian Value Package (CVP), Mainstreet, Crew, Crew Lux, SXT, R/T Crossroad)
  • 2011–present Jeep Grand Cherokee (Models: Laredo "E", Laredo "X", 70TH Anniversary Edition, Trailhawk, Altitude Edition, Limited, Overland, Overland Summit Edition)
  • 2011–2014 Volkswagen Routan (Models: S, SE, SEL, SEL Premium)
  • 2012–present Fiat Freemont
  • 2012–present Jeep Wrangler (Models: Sport, Unlimited Sport, Sport "S", Unlimited Sport "S", Freedom Edition, Unlimited Freedom Edition, Altitude Edition, Unlimited Altitude Edition, 70TH Anniversary Edition, Unlimited 70TH Anniversary Edition, Sahara, Unlimited Sahara, Moab, Unlimited Moab, Rubicon, Unlimited Rubicon, Rubicon 10TH Anniversary, Unlimited Rubicon 10TH Anniversary)
  • 2012–2015 Lancia Voyager (Models: Limited)
  • 2012–2014 Lancia Thema
  • 2012–2015 Ram Cargo Van (Models: C/V Base, C/V Tradesman)
  • 2013–present Ram 1500 (Models: Tradesman, SLT, HFE)
  • 2014–present Ram ProMaster
  • 2015–2016 Chrysler 200 (295-hp, 262-lb ft)



Related Videos

Related Articles

By YOUCANIC on Jan 18, 2019


Disclaimer: Youcanic has made every effort to assure the accuracy of the information on this page. Neither Youcanic nor its affiliates assume responsibility for any loss or damage due to any errors, omissions, lack of information. You agree to hold Youcanic free from any liability arising out of the use of any information contained within. All pictures and references to trademarks and car names are for reference only and do not imply an association with the manufacturer. Consult your owner's manual or authorized factory manuals when performing repair procedures. By entering this site, you agree to our Terms & Conditions and Privacy Polity.