| › BMW

How to change front brake pads on a BMW

In this guide, you will find step-by-step instructions on how to change the front brake pads and rotors on BMW vehicles.

The pictures in this guide are from a BMW 5-series. Because BMW uses a similar front brake setup, these instructions should be helpful to owners of other models including 1-Series, 3-Series, 6-Series, 7-Series, X1, X3, X5, Z3, Z4 with the exception on the M series.

What you notice

bmw front brake pad worn message
  • Brake Pad Warning Message on iDrive - A warning message reminding you that your BMW front brakes are worn below the minimum depth. 
  • Noise when breaking -Screeching, grinding, squealing, rubbing and other noises are common symptoms that your brake pads are worn. When the pads wear thin, it causes a metal-on-metal scenario as the brake pad wear indicator rubs against the rotor.
  • Brake Pedal - You may need to press brake pedal harder or down farther to complete braking.
  • Brake Light On- Another symptom of worn brake pads is the brake light coming on. 

What you will need

  • BMW Front Brake Pads - Some popular brands that make BMW brake pads and discs are BOSCH, STARK, SACHS, SKF, VAN WEZEL, VALEO, LuK, MAPCO, A.B.S., ATE. Ceramic brake pads are recommended for best performance, longer life, and low dust.
  • BMW Front Rotors - Replace the rotors especially if they have created a lip on the outer edge or your BMW steering wheel shakes when braking.
  • BMW jack adaptor -  Prevent your BMW jack points from bending when using a jack to lift your car. For most late model BMW or Mini vehicles.
  • BMW Brake Wear Sensor - You will need to replace the brake wear sensor in order to reset the brake warning light. 
  • Allen key set - Needed to remove caliper guide pins.
  • Jack and Jack Stand - You will need these to raise the vehicle and secure it. Wheel chocks can be used as well to prevent the car from rolling back. Your car should have a jack in the trunk. You will need to buy jack stands
  • Lug wrench - A wheel lug wrench is needed to loosen the lug nuts. Your car should already have a lug wrench in the trunk. 
  • Gloves - You need to protect your hands. 
  • C - Clamp - Use a C clamp to press the piston into the caliper. You will not be able to fit the new brake pads without pressing the piston. 
  • Glasses - protect your eyes from flying metal pieces. 
  • Brake & Caliper Grease - Use it to prevent noise from brake pad vibrations. Can be used on shimmed disc brake pads, drum and ABS systems. Use only on metal to metal contact points. Do not use on the cotact surface between brake pad and rotor. 
  • Tool Box - A toolbox that has metric sockets from 6mm to 19mm and a 3/8 ratchet
  • Breaker Bar - In case you need to break loose a rusted bolt. 
  • Penetrating Oil - Break free rusted and corroded parts. 
  • Torque wrench - Make sure you use correct procedures and torque values.

Before you start

  • We recommend that you review these Auto Repair Safety Rules before you get started with replacing the front brakes on your car. 
  • Always make sure you use correct procedures and torque values.
  • Never rely on jack to support a vehicle. Always use jack stands in addition to the jack. 

Instructions

Jack up the car

Get the lug nuts loose but do not remove them yet. Next, raise the vehicle and secure it with jack stands. Place wheel chocks behind the rear wheels to prevent your BMW from rolling back. Ensure the parking brake is engaged. 

remove bmw wheel

Remove the wheel

With the car jacked up and secured by jack stands, you are now ready to get started on replacing front brake pads on your BMW. 

bmw brake pad diy

Remove the brake wear sensor

Use a flat head screwdriver to pry out the wear sensor from the brake pad. If you don't notice a brake wear sensor, don't worry. It will be installed on the other side. BMW typically uses only one brake pad wear sensor per axle. If you need help with this step follow these instructions on how to replace BMW brake wear sensor. 

remove bmw wear sensor before replacing front bmw brake pads

Remove anti-rattle retainer

Use a prybar or a screwdriver to try out the anti-rattle retainer. This clip puts pressure on the brake caliper and prevents the brake pads from making a squeaking noise. Insert the screwdriver and pry it out. 

bmw front brake pad diy pad anti rattle retainer

Loose two bolts on the rear of the caliper

Remove the two dust caps on the back of the brake caliper. The caps do not screw. You simply pry them out. Next, you need to loosen the brake caliper bolts (guide pins). Use a 7mm Allen wrench to remove the brake caliper bolts. 

bmw front brake pad guide pin cap

bmw front brake pad guide pin

 

Remove caliper and brake pads

Remove the brake caliper from the wheel hub. If the caliper does not come off easily, use a flat screwdriver to pry one of the brake pads away from the rotor. 

remove bmw front brake pads from disc

Press caliper piston in

With the caliper removed and the inner pad still connected to the brake caliper, use a C-clamp or any compression tool to push the piston back into the caliper. This is necessary otherwise the brake caliper will not fit on the rotor when you try to install the new BMW brake pads. 

Install new brake pads

Remove the old brake pads. Install the new brake pads on the caliper. Tie the brake caliper to the strut. Do not allow your BMW brake caliper to hang by the brake hose. Also, make sure to inspect the brake hose for cracks. If brake hose shows signs of cracks follow this guide on how to replace BMW brake hose. 

installed new bmw front brake pads

Remove brake caliper bracket

Now that you have removed the front brake caliper on your BMW, you will need to remove the brake caliper bracket or what is known as the caliper carrier. There are two 16 mm (sometimes 17mm or 18mm) bolts on the back that you need to remove. To break these bolts loose you may need to use a breaker bar

remove bmw front brake carrier bolts

Remove rotor 

With the brake caliper bracket removed from the steering knuckle, you are ready to remove the rotor. First, you need to remove the set screw. This will allow you to take off the rotor. If the rotor is rusted it will be difficult to remove your BMW rotor from the wheel hub. Spray some penetrating oil and wait 10 min. Next, grab a rubber hammer and hit the rotor on the back several times until the rotor gets loose. 

bmw rotor set screw

bmw rotor won't come off spray penetrating oil

remove front bmw rotor disc

Clean wheel hub

With the rotor removed, the wheel hub is exposed. Clean the wheel hub surface where the rotor sits with a clean rag or if rust is present scrub it with a wire brush. Apply a very thin coat of anti-seize to the face of the wheel hub to make it easier to remove the rotor next time. 

clean bmw wheel hub

Install new rotor

Install the rotor on the wheel hub and thread in the set screw. Don't need to over tighten the set screw. It is there to simply keep the rotor in place when the wheel is removed. 

install new bmw rotor

Install brake caliper carrier bracket

Next step is to install the brake caliper bracket. Clean any dust or debris from areas where the bracket contacts the brake caliper or brake pads. Install the two bolts that hold the carrier bracket in place.

Torque the two bolts to 80 ft - lbs or as recommended by BMW for your particular model. 

clean bmw brake caliper bracket before installing it

bmw brake pad carrier installation

Install brake caliper

Install the brake pads on the brake caliper. Place the brake caliper and pads on the rotor and thread the guide pins. Rember to install the anti-rattle bracket. 

install new bmw brake pads and rotors

Install wheel

Install the wheel and torque the lug nuts to 90 ft-lbs. 

bmw brake pad diy

Check brake fluid level

Check the brake fluid level. Add BMW brake fluid if the level is below the min mark.

Follow this guide on how to check or add BMW brake fluid

Reset BMW brake service light

Once you replace both front brake pads on a BMW, you will need to reset the brake light.

You can perform BMW brake pad reset via the ODO reset button on the dashboard.

If you are not able to reset your BMW brake light, follow these instructions to figure how why you can't reset BMW brake light reminder. 

bmw brake light reset instructions

Test brakes

Before driving off, start the engine and press the brake pedal a few times. At first, the brake pedal will feel soft and go all the way to the floor.

After two to three pumps of the pedal, the brakes will feel normal again. 

installed new bmw brake pads

Average cost to replace BMW brake pads

To change just the front brake pads on a BMW, expect to pay between $180-$250. That's for pads only.

In many cases, the rotors need to be changed in addition to the brake pads. In such cases, the typical cost to change BMW front brake pads and rotors can vary from $380-$600.

That would be for brake pads and rotors on both front wheels. Brake pads and rotors are usually changed as a set. 

FAQ

How many miles can I drive a BMW after getting the brake pad warning? 

  • The range can vary, but typically you will be able to get another 300-500 miles. If brake pads wear to the point that the pad metal is contacting your brake rotor, you will damage the rotors. In such cases, the rotors must be replaced as well.  If you’re the kind of driver who stops abruptly frequently, you’ll need to replace your brakes pads and rotors more often than drivers who slowly come to a stop.

Additional Resources

This is a list of helpful resources that can further help you successfully change front brake pads on a BMW.

check bmw brake fluid level

By YOUCANIC on May 20, 2019

Vehicle

Disclaimer: Youcanic has made every effort to assure the accuracy of the information on this page. Neither Youcanic nor its affiliates assume responsibility for any loss or damage due to any errors, omissions, lack of information. You agree to hold Youcanic free from any liability arising out of the use of any information contained within. All pictures and references to trademarks and car names are for reference only and do not imply an association with the manufacturer. Consult your owner's manual or authorized factory manuals when performing repair procedures. By entering this site, you agree to our Terms & Conditions and Privacy Polity.