Skip to main content

Ford Check Engine Light Stays On

The check engine light (CEL) or service engine soon (SES) light on a Ford may come on due to a loose gas cap, worn spark plugs, faulty ignition coil, bad oxygen sensor, and other issues. 

This guide provides instructions on how to reset Ford check engine light and common problems that turn on the check engine light on Ford vehicles. 

Ford Check Engine Light Stays On
DIY COST $20-$150

Ford check engine light will turn on when you turn on the ignition under normal operation but should turn off and stay off once you start the engine.

What does it mean when the Ford check engine light comes on? 

If the check engine light in your Ford comes on when driving, it means the On-Board Diagnostic (OBD) system has detected a problem with the engine or emission system. If the check engine light is flashing, it indicates a severe engine misfire which allows unburned fuel to be dumped into the catalytic converter.


Ford check engine light stays on

Here are some of the most common symptoms owners notice when their Ford check engine light stays on.

  • Ford may idle or run rough
  • A decrease in fuel economy
  • The engine won't stay running
  • Ford loses power or is stuck in gear.
  • Hesitates during acceleration
  • Powertrain malfunction/Reduced power - this message comes on when a powertrain problem has been detected.

In some cases, the Ford check engine light comes on, and no other symptoms are noticed.

How to Reset Ford Check Engine Light 

The first step in troubleshooting the check engine light is to read the fault codes with an OBD-II scanner

  1. Locate the diagnostics port under the dashboard of your Ford.Ford OBD II port locaiton
  2. Connect your OBD-II scanner to the diagnostics port. Turn on the ignition by pressing the Start button without pressing the brake pedal. turn on ignition to read ford check engine light
  3. Allow the scanner to power up.
  4. Select Engine Module, then press read to retrieve codes that have triggered your Ford check engine light. These are the codes that have triggered the check engine light on your Ford.
  5. Once you fix the problem that triggered the code, come back to the main menu and select Erase Fault Data.


Your Ford check engine light on causes vary. Without reading Ford check engine diagnostic trouble codes (DTC), it is difficult to know the problem.

These instructions work on 1996 and newer Ford vehicles, including Ford Mustang, Focus, Fiesta, F-150, Ranger, Explorer, EcoSport, Escape, Fusion, F250, Expedition, Edge, Transit, Taurus, Flex, Shelby GT, C-Max made in the USA. On European models, vehicles must be 2000 or newer. 

Common Problems That Trigger Ford Check Engine Light

Ford Engine

This is a list of the most common problems that trigger Ford's check engine light to stay on. 

Hundreds of possible causes will turn on the Ford check engine light. To find out why the check engine light is on in your Ford, read the fault codes. 

Let's look at some of the most common problems and codes that often cause the check engine light to stay in a Ford vehicle. 

Loose Gas Cap

Loose gas cap triggers Ford check engine light

One of the most common triggers of the check engine light on a Ford vehicle is a loose gas cap. If you recently stopped at a gas station, make sure the gas cap was properly tightened.

In some cases, the O ring in the fuel cap gets damaged. If that's the case, you will need to replace the fuel cap. You can use an OBD-II scanner or drive the vehicle for a few days for your Ford engine computer to reset the check engine light.

Newer Ford vehicles equipped with Easy Fuel have no gas cap at all.

Mass Air Flow Sensor

ford check engine light on due to maf sensor


Often referred to as the MAF sensor, the mass airflow sensor can fail, triggering the Ford check engine light to come on. If your Ford MAF sensor is defective, you will notice engine hesitation during acceleration and a dramatic fuel economy decrease.

Typical codes are stored in the ECU when the MAF fails P0171 and P0174. Resetting these codes by disconnecting the battery for a few minutes does not fix the problem. In a few cases, you may fix this problem by using a MAF sensor cleaner.

The recommended fix is to replace your Ford Mass Air Flow Sensor with a new OEM Ford unit. Aftermarket Ford MAF sensors can sometimes malfunction even when brand new.

Oxygen Sensor

The oxygen sensors (O2) mounted on the catalytic converter can fail to cause the check engine light to come on, poor engine performance, and a decrease in fuel economy.

One of the most common Ford codes related to the oxygen sensor is P0132, caused by an oxygen sensor circuit high voltage.

VCTR Solenoid

A common problem that triggers the check engine light on Ford vehicles, especially Fusions equipped with the 4 cylinder engine, is a defective Variable Camshaft Timing solenoid known as VCT solenoid.

A defective VCT solenoid will cause the engine to run rough and trigger the check engine light simultaneously. The code related to this problem is usually P0012 - "A" Camshaft Position - Timing Over-Retarded (Bank 1). Related codes include P0011, P0010, P0013, P0014.

Ignition Coils

Bad Ford spark plugs trigger check engine light on

The ignition coils may fail, triggering the Ford check engine light to come on. Common symptoms include check engine light on but engine misfire, running rough, and fault codes ranging from P0300 through P03012.

It is recommended to change the spark plug boots at the same time. If your Ford check engine light stays on after replacing the ignition coils, check the MAF sensor, spark plugs, catalytic converter, and the ECU.


There are hundreds of possible problems that can cause Ford check engine light to come on. The most common issues are spark plugs, oxygen sensors, and catalytic converter failure. Instead of guessing what is wrong, use an OBD-II scanner to read the fault codes. 

What does it mean when Ford check engine light flashes? 

If the check engine or service engine light is flashing, it means that the OBD-II system has detected an engine misfire. This is often caused by a bad spark plug or defective ignition coil but can be caused by other issues.

When your Ford check engine light is flashing, fuel is not getting burned in the cylinder but is existing unburned and typically gets burned at the catalytic converter.

Avoid driving your Ford if the check engine light is flashing, as this condition may cause unnecessary damage to the engine and the catalytic converter.

Ford Check Engine Light Flashing 8 Times

If your Ford check engine light blinks eight times when you turn on the ignition, it means that it is not ready for State Emission Inspection, I/M test. This typically happens if the codes were recently erased with an OBD-II scanner or the battery was disconnected.

As long as the lights stop blinking after eight flashes, you can continue to drive the vehicle. All systems should be tested within a few driving cycles, and the CEL should no long flash at startup.

Frequently Asked Questions

Can I reset the check engine light by disconnecting the car battery?

  • Yes, disconnecting the battery usually clears the ECU codes. By turning the check engine light off this way, you will not fix the problem. If you believe the check engine light needs to be off, drive the car for a few days, and the CEL will reset itself. The Onboard Diagnostic System in your car continually monitors your vehicle and will turn off the CEL if the problem is solved. If the problem hasn't been resolved, even if you disconnect the battery, the CEL will come back up again, which can be as soon as you restart the car or up to a few days.

Will my car pass safety emissions if the check engine light is on or recently reset?

  • If the check engine light is on, it will not pass the emission inspection/smog test. If the light was recently reset with an OBD2 scanner or by disconnecting the battery, you need to drive the car for a couple of days for the systems to be ready for testing.

Check engine light is on but no codes?

  • It could be because you are using an OBD2 scanner that does not support the protocol used in your car. Try a different scanner. Also, there may be an issue communicating with the ECU due to a damaged wire or ECU malfunction.

Would the check engine light on cause the car to not start?

  • No. The check engine light is not the reason why the car doesn't start. If the car doesn't start, read the codes, and maybe the CEL will give you a code that can help you diagnose the car. Clearing codes will not make your car start.

Why is my check engine light came on after the oil change?

  • It may be just bad timing. An oil change is not going to trigger the CEL. Unless a sensor is accidentally unplugged, disconnected, or damaged during the oil change, take your car back to the auto repair shop that changed your oil and have them diagnose the problem.

Is it normal for the check engine light to turn on after repair service?

  • No, the CEL should not turn on after routine maintenance. If you modified your engine, transmission, exhaust, intake, fuel system, or other systems, it could affect the engine and emission control system, causing a check engine or service engine soon light to come on. CEL should not come on if you changed tires or tire size.

Why is my check engine light on after replacing the battery?

  • Drive the car for a couple of days and allow the ECU to reset itself. If the CEL remains on, read codes.

Why did my check engine light turn on when the engine overheated?

  • The check engine light is trying to tell you that there is a problem with your engine. It could be low coolant, stuck thermostat, transmission not shifting. Figure out why your car is overheating first and address that problem. Do not drive if the car overheats. Pull over and turn off the ignition. 



2015 F350XL gas engine. Dead battery. Replaced battery--truck will NOT start (console displays STARTING SYSTEM FAULT). Terminals clean & tight. No corrosion. All fuses verified good. My CEL flashes 8 times when Ignition key is turned but no Start. Also tried jump start from another vehicle--no Start. All lights, wipers, etc operate so electrical power is available. Cannot OBD because computer memory was cleared--no record of codes available. Any ideas? Please!

Jesus Gutierrez

In reply to by Visitor

I changed my fuel pump on my 2012 Ford fusion 3.0 fuel felx and my car cranks but no start.all fuses are good fuel pump is working now . don't know what to do about it now I can't get it to start


Question 1 : Can this device/scan tool able to detect injector DTC code for repair besides that as demonstrated online here? Question2 : Does this device/scan suits vehicle sold in Asia- Thailand or Malaysia ? Question: 3 if YES to Question 1, does resetting of new injector NEW CODE necessary/compulsory ?

Kim Sparks

2000 explorer xlt- won't go into gear. It will shift but will not actually go in gear it just sits there


While driving, I hit a pothole and my Tyre bust. I stopped and the car does not want to start anymore. Engine light comes on and disappears immediately after turning the key on
Most Fords and other vehicles have a fuel shut off switch which gets tripped during accidents. Usually located in the Hatch of small cars, behind the panels. Best thing is to Google where your fuel shut off switch is. If you have the owners manual, even better.


The check engine light came on when display in fuel economy- ford pass message malfunction indicator lamp regulatory the power train module has detected that fuel signal has repeatedly moved in & out of normal operating range- truck has done twice dealershipcould not locate issue after second time doing this now fueleconmony display is no longer an option this is 2020 ford Ranger with 2451 miles ( still new- lol)

Add new comment

Plain text