In some cases, such as EVAP leaks, the check engine light may come on, but no performance issues seem present. Fuel consumption may be higher than normal.
How to Diagnose and Reset Land Rover Check Engine Light
With a check engine light on, you need to find out what caused it. In this section, you will learn how to use an OBD-II scanner to read codes and reset the Land Rover check engine light.
Locate the OBD-II port under the dashboard. Plugin your scanner into the port.
Turn on the ignition but do not start the engine.
Enter the Engine Control Module (ECM) by selecting it.
Scroll down to Read Codes and press enter. All fault codes will be displayed on the screen, along with a short description of the problem.
Fix any problem that came up on step five. Come back to the main menu and select Clear Fault codes instead of reading codes.
If resetting the Land Rover check engine light without fixing the underlying problem, the check engine light will come back on. Depending on the problem, the check engine light may come back on as soon as you restart the engine or it could take up to a week.
What causes problems trigger the Land Rover check engine?
Common issues that trigger the check engine light on Land Rover vehicles.
In addition to the causes listed above, the following problems are common issues that affect Land Rover vehicles.
Timing Chaing - Newer 4.4-liter V8 engines are prone to timing-related problems caused by chain guides that wear out. Early symptoms are intermittent knocking and metallic rattling from the engine bay, usually more prominent during deceleration. With time, chain tension can wear to the extent to cause a 'check engine' light. You might also experience a loss of power, sluggish acceleration, and poor idle. Although the most common code is a 'crankshaft/camshaft correlation,' you might get some other timing-related codes. Related DTC: P0016
Crankshaft Position Sensor - If your Land Rover has intermittent starting issues, look for stored codes related to the crankshaft position sensor. The problem usually starts as an occasional crank-but-no-start situation, especially when the engine is hot. With time, it can display other symptoms, such as misfire, cutting out, and stalling. Related DTC: P0335
Mass Air Flow Sensor - In the case of a 'check engine light triggered by various Systems to lean codes, the first thing to check is the MAF sensor. Although cleaning with special MAF fluid might help, the sensor will need to be replaced in most cases. Other possible causes for these codes are various vacuum leaks. Related DTC: P0170 “ P0174
Fuel Pump - Models with 4 cylinder TD4 diesel engines are known for going into limp mode without any apparent reason. When that happens, the engine will not go over 3000 RPM, there will be no boost from the turbocharger, and you will notice a considerable loss of power. This issue can be caused by a faulty low-pressure fuel pump located in the fuel tank. DTC: P1260
Intercooler Hose All Land Rovers with 2.2-liter diesel engines can have a damaged top intercooler hose. This is actually a design flaw, as the hose chafes on a nearby bracket. In addition to a 'check engine' light, you will experience a lack of power and acceleration, combined with a hissing sound from the engine bay. When replacing, make sure to install a modified intercooler hose. Related DTC: P0101
Shift Solenoids - With an automatic gearbox, you might notice hesitation when shifting or even an intermittent inability to shift into 3th and 4th gear. This is caused by sticking shifting solenoids, which is a result of poor maintenance. Try changing gearbox oil and filter, and if that doesn't help, replace shift solenoids. Related DTC: P0783
What does it mean when Land Rover Check Engine is Flashing?
If your Land Rover check engine light is flashing on and off, it indicates a misfire on one or more cylinders. Typically this is caused due to a bad spark plug, faulty ignition coil or could indicate a clogged catalytic converter.
Do not drive or keep the engine running if the check engine light is flashing. To prevent any additional engine or catalytic converter damage.
Check engine light is present on all 1996 and newer Land Rovers, including Discovery, LR2, LR3, LR4, Discovery, Evoque, Defender, etc.
There are hundreds of possible problems that can cause the check engine light on your Land Rover to stay on. The most common issues are spark plugs, oxygen sensors, and catalytic converter failure. Instead of guessing what is wrong, use an OBD-II scanner to read the fault codes.
Add new comment
Troubleshooting Land Rover Check Engine Light This guide will discuss common problems that trigger the check engine to come on a Land Rover and how to read and reset it.