Skip to main content

Mazda Mass Air Flow (MAF) Sensor | Symptoms | Repair

In this guide, you will learn about the symptoms of a bad Mass Airflow sensor (MAF) on Mazda vehicles and how to replace it yourself. 

When the mass airflow (MAF) sensor on a Mazda fails, the check engine light will turn on, and several performance issues will be noticed.

Mazda Mass Air Flow (MAF) Sensor | Symptoms | Repair
ESTIMATED TIME 15 min
DIY COST $15-$35
DIFFICULTY Very Easy

 

Symptoms

Here is a list of possible symptoms you may notice from a bad mass airflow sensor on a Mazda.

How to replace the mass airflow sensor on a Mazda

mazda maf replacement guide diy 3 5 6 cx5 cx7 cx9

What you will need

Procedure

  1. Let the engine cool down. Next, open the hood of the Mazda and disconnect the battery.
  2. Locate the mass airflow sensor on your Mazda 5. The sensor is located near the engine air filter housing. diy guide how to change mass air flow sensor Mazda 5 2010 2011 2012 2013 2014 2015 2016 2017 2018

  3. Unplug the wire harness. Next, unplug the electrical connector from the Mazda mass airflow sensor.  location of MAF sennsor on Mazda

  4. Remove the screws that hold the mass airflow sensor in place. 
  5. Install the new MAF on your Mazda. Tight the screws so that they are snug.

  6. Plug the electrical connector until it locks in place. 

  7. Close the hood and start the engine. 

If the check engine light is on, don't expect it to turn off right away. If no other fault codes are present, the check engine light should reset within a week. 

If you want to check for other codes or reset the check engine light, use an OBD2 scanner to clear the fault codes. The OBD2 scanner can be connected to the diagnostic port located under the dashboard on the driver's side.  

Mazda Mass Air Flow Fault Codes

Possible fault codes that may be triggered by a bad mass flow sensor on a Mazda.

Other DTCs not listed here may be related to the MAF sensor

How to tell if the mass airflow sensor is bad on a Mazda?

When the mass airflow sensor fails, your Mazda will not accelerate properly; it may misfire and trigger the check engine light or service engine light. To confirm that the MAF is the problem, always read the fault codes using an OBD2 scanner.

Can I clean the Mazda airflow sensor?

Yes. You can clean a Mazda airflow sensor using an Air Flow Sensor Cleaner. No guarantee cleaning will fix the problem. Cleaning is successful in cases when the sensor has gotten dirty.

How much does a new Mazda air flow sensor cost?

At the dealership, it will cost anywhere from $200 to $300. Online the MAF sensor can be bought for as low as $50. 

Can I replace the MAF on a Mazda myself?

Yes. It is one of the simplest Mazda DIY repairs. If you are starting with DIY auto repair, this will be an easy task to get started.

Where is the Mass Air Flow sensor located on a Mazda?

It is located on the engine air filter housing or the large diameter air intake hose that connects the air clear box to the engine intake manifold.

Step-by-step instructions on how to change the mass airflow sensor on a Mazda. These instructions include pictures and video clips to help you with this Mazda DIY repair.

 

Comments

Visitor

My check engine light came on. My 2010 madza 3 mass air flow sensor showed to be bad. I had a new one put on and within 3 hours the light came back on. We cleared the computer and again the light came back on. It still showed the air flow censor. Thought maybe I got a bad censor so I replaced it with another new one. Light went off but came back on a few hours later. Still showed the same sensor. Now my car is surging and stalling and even dieing on me. I can't figure it out. Any suggestions?

Visitor

Great article. I got quoted 280 from the dealership to charge the MAF on Mazda 6. Can t believe I am going to save $200. :)

Visitor

How to unplug the wire wire harness form the MAF sensor? I can't get it off. Regards

Selece Reeves

In reply to by Visitor

Did you disconnect the battery, you have to do this so your car will forget the parameters of the old MAF sensor and default back to factory settings, it will then learn the new parameters. I had to do this to my 2012 Mazda 6 itouring.

Add new comment

Plain text

Notes

Safety Tips

Auto Repair Safety Notes