Car batteries have a lifespan of about three to five years. We recommend checking the battery in your car monthly after the three-year mark to keep your car running smoothly. Routine battery testing helps prevent unexpected failures and identifies potential issues before they leave you stranded. This guide will show you how to use the YOUCANIC Battery Tester for an accurate diagnosis.

Signs That You Have a Bad Battery

  • Flickering infotainment system with the dashboard.
  • Battery warning light on the dashboard.
  • Performing frequent jump-starting of the vehicle.
  • Failure of electrical system. (e.g., slow up and down of the power windows).
  • Slow engine cranking.

What Does a Bad Battery Look Like?

  • Bloated Battery: A bloated battery can be visually checked or can be felt by touch. A bloated battery may explode at any time. This happens because of overcharging or aging of the battery.
  • Broken Positive or Negative Pole: Look for any sign of corrosion that may lead to a leak from the poles or check for the physical appearance of the pole itself. An over-tightening of the cable connector may damage the battery poles.
  • Crack in the Casing -Look for any sign of a crack in the whole body of the battery, The crack may lead to leaks and a bad smell coming from the battery. Cracking happens if the battery support is overtightened and sometimes because of looseness, due to the movements and vibration in the vehicle, the battery may bump over time. The crack may be caused also by the bloated battery.

Step-by-Step Instructions

  1. Make sure that your Volvo is parked on a level surface and the engine is off.
  2. Find and pull the hood release lever on the driver’s side near the floor.
  3. Walk to the front of your vehicle, find the hood safety latch under the front hood, and lift the hood upward after releasing it.
  4. Secure the hood prop rod to keep the hood open.
  5. Find the battery towards the back of the engine bay, and remove the cover and rubber molding.
  6. Connect your YOUCANIC tester to the battery jump start points if accessible. Connect your red clamp to the red positive terminal first and then your black clamp to the negative terminal.


    .
    👍Pro Tip: If the battery terminals are corroded, wear gloves and clean them to ensure proper connection and energy output.
  7. Make sure all clamps are securely in place before testing.Battery Terminals
  8. Enter the battery specifications from the rating label into the tester, and select the correct battery type (AGM, Lead-Acid, etc.).
  9. Review the test results and compare them to your vehicle’s dashboard indicators. Document these results for future reference.
  10. To remove the clamps from the battery terminal, remove the negative (-) first, then the positive (+).

Test Result Interpretation

  • Battery Voltage
  • Battery State of Charge (SOC) Condition
  • Battery State of Health (SOH) Condition
  • Charging Condition
  • Engine Cranking Condition
Battery Test Result - Volvo: How To Check The Car Battery Condition
  • Warning Light or Warning Message Present on the Dashboard: Normally, removing the negative or positive terminal of the battery can trigger fault codes. Sometimes you will not see any warning message in your dashboard but it has already registered fault codes in the vehicle. Delete the fault codes by using an OBD-II scanner to prevent any issues.

Important Notes

  • Make sure that the engine is turned off including the electrical components of the vehicle before starting the job repair.
  • Do not forget to clean the battery connections for proper fit and good contact for better electrical output.
  • Document the battery age, including when it is replaced with the reading result before it is installed in the vehicle.
  • Check related systems, such as charging conditions that may affect the discharging of the battery.
  • Inspect for any electrical modification on the vehicle that may discharge the battery at any time. Use the YOUCANIC Battery Tester for parasitic draw detection.
  • If the battery needs to be replaced, see our guide, “2016-2025 Volvo XC90: How to Replace the Battery,” for more information and step-by-step instructions.
  • Remember to record your test results for future reference.

Safety Precautions

  • Use proper jump-start locations. The red cable is to the positive terminal of the battery and the black cable is to the vehicle body ground.
  • Follow the correct terminal sequence. In removing the battery, disconnect the negative terminal first before the positive. When installing the battery, the positive must be connected first before the negative.
  • Wear personal protective equipment to avoid any accidents during your repair. Use gloves and goggles to protect yourself.
  • Use the correct or appropriate tools to prevent damaging the parts.
  • Maintaining proper ventilation in your work area allows you to move freely and for your safety.

Post-Test Verification

  • Verify if the battery is in good condition by using the YOUCANIC Battery Tester
  • Monitor the charging condition.
  • Check all the exterior and interior lights if they are all illuminating properly.
  • Operate the buttons of power windows, horn, and sunroof if have, and verify if they are operating properly. Perform initialization or resetting if the one-touch automatic function is not working. Pressing the buttons fully close or fully open for about 5 seconds may reset the one-touch automatic function to go back to its normal operation.
  • Verify if no fault codes are registered using the OBD-II scanner. Delete the DTCs and make sure no fault code is registered.
  • Document your findings for future reference. You may save the results of your job repair using the YOUCANIC OBD-II scanner.

Experts Who Contributed to This Article

Elbert Nonog

Elbert Nonog, Automotive National Cert., BS Mechanical Eng.

Diagnostic Specialist13+ years of experience

Elbert G. Nonog is an Automotive Technical Writer and Training Manager with over 10 years of experience across major brands including Chevy, MG, Ford, Volkswagen, and Toyota. Rising from technician to leadership roles, Elbert excels at transforming complex automotive concepts into accessible training materials and documentation. His expertise spans conventional and electric vehicle systems, nationwide dealership training, and aftersales operations management. With TESDA certification and pursuing further education from the Technological University of Philippines, Elbert effectively bridges the gap between automotive engineering and practical application for industry professionals and enthusiasts.