Mercedes W205 Rear Brake Pad & Rotor Replacement Instructions
Worn brake pads announce themselves with squealing or grinding, longer stopping distances, a brake pedal that sits lower than it used to and often a wear warning light on the dashboard. What they do not cause is a soft or spongy pedal. If your pedal feels springy, travels further than it should or sinks slowly toward the floor, that is air in the hydraulic system, a fluid leak or a failing master cylinder, and fitting new pads will not fix it. Find that cause before driving the car. If your symptoms are wear related, the procedure below covers the job.
At a Glance
- Fits: Mercedes C-Class W205
- Electric parking brake: put the rear calipers in fitting position through the cluster first
- Path: ignition on, hold OK and the phone button, then choose brake pad replacement
- Lug nuts: 17mm
- Also replace: the rear pad wear sensor if the warning light was on
When servicing your brakes, one thing to consider is whether you should change just your brake pads or both the brake pads and rotors. Mercedes recommends changing them both at the same time.
Replacing rear brake pads on Mercedes W205 is a fairly easy job. The only specific step is releasing the electric parking brakes, as it uses the same caliper as the main brake. However, this can be done without any special tools.
🔧 Find out what is actually wrong before you pay someone to guess
Dealer level diagnostics at home with the YOUCANIC UCAN-II Pro.
- ✔ Covers most makes and models, including many luxury brands. Send us your VIN and we will confirm your car before you order
- ✔ Reads every module, not just the engine, so you find the faults a basic reader says are not there
- ✔ Commands the car: test a fan or pump, bleed ABS, retract an electronic parking brake, register a battery
- ✔ No subscriptions. Free lifetime updates, so the price you pay is the whole price
- ✔ Backed by real mechanics in the USA you can email before and after you buy
Featured in The Wall Street Journal
What you will need
- W205 Rear Brake Pads & Rotors
- With wear sensor
- PN: A1695401617, A0004208200, 0004208200
- Mechanic tool set metric
- Low profile jack
- Jack stands
- Wheel chocks
- Torque wrench
- Breaker bar
- Flathead screwdriver
- Brake caliper spreader
Procedure
- While the vehicle is still on the ground and with the parking brake on, use a breaker bar and a 17mm socket to break free all rear-wheel lug nut bolts.

- Open the hood and locate the brake reservoir. During this procedure, extract a small amount of brake fluid from the reservoir to prevent it from overflowing. When you are done, fit the brake fluid reservoir cap.
- Block front wheels to prevent the car from any movement
- Inside the car, turn on the ignition and press and hold both OK and Telephone buttons on the steering wheel until the vehicle data menu appears.

- Use the arrow button to navigate to brake pad replacement, and press OK to move the rear brake caliper to the fitting position. You will hear the movement from the back as the brake calipers retract. Also, the ABS light will illuminate, and the red brake warning light will flash to confirm that the fitting position is active.

- Locate rear lighting points, lift the rear of your car in the air using a jack, and secure it with jack stands.

- Remove all wheel lugs and remove the wheel itself.

- Using a suitable screwdriver, remove the anti-rattle bracket.

- Using a thin screwdriver. Disconnect the brake pad wear sensor from its harness.
- At the backside of the caliper, remove the black plastic caps to gain access to guide bolts.

- Remove the guide pins using a 7mm hex key socket.

- Pull the caliper off the brake rotor. This may take some wiggling.
- Brake pads will remain seated within the bracket, so you must slide them out.
- Using a brake pad spreader tool, spread out brake pistons to make enough room for new, thicker brake pads.
- Before installing new pads into the caliper, fit the new brake sensor to the outer one.
- Install new brake pads into the bracket and pull the sensor wire through the slot in the caliper.
- Refit the brake caliper onto the bracket and tighten the bolts to 25 ft-lbs using a torque wrench.
- Connect the brake pad wear sensor to its harness
- Refit all remaining parts in reverse order
- Repeat the procedure on the other rear wheel
- Lower the car on the ground and torque all-wheel bolts to 96 ft-lbs using a torque wrench.
- Push the brake pedal several times until it gets hard, then top off the brake fluid reservoir.
- Back inside the car, exit the fitting position by pressing OK on the steering wheel. You will hear the movement from the back as the brake caliper squeezes and calibrates its position. After this is done, press OK to confirm.
- Start the engine and press the brake pedal several times until the pedal feels hard again.
Torque Specifications
- Wheel bolts: 96 ft-lbs
- Rear caliper guide bolt: 25 ft-lbs
After the Brake Job
- Before moving the car, pump the brake pedal until it feels firm. The pistons need to move back out against the new pads.
- Check the brake fluid level and top up to MAX if needed.
- Bed in the new pads: make several moderate stops from about 35 mph to 5 mph without coming to a full stop, then drive a few minutes to let the brakes cool.
- Recheck the wheel lug nut torque after the first few miles.
Still Noisy or Pulling After New Pads?
- Squeal: missing shims or no brake grease on the pad backing plates and slide points.
- Grinding: a pad installed backward or a stone caught between the rotor and dust shield.
- Pulling to one side: a sticking caliper slide pin or piston on that side.
- Vibration: rotors that are warped or were not replaced.
Brake pad menu missing or calipers will not retract?
If the brake pad replacement option does not appear in the cluster, or the calipers do not move, the electric parking brake can be put into service mode with a scan tool. The YOUCANIC UCAN-II Pro includes an electric parking brake service function on supported models. Never force the piston back with a C clamp while the parking brake motor is engaged.
Frequently Asked Questions
How do I retract the rear brakes on a Mercedes W205?
With the ignition on, hold the OK and phone buttons on the steering wheel to open the vehicle data menu, select brake pad replacement and confirm. The calipers move to the fitting position.
Do I need to replace the brake pad wear sensor?
If the brake wear warning light came on, yes. The sensor is worn through and must be replaced with the pads.
How do I exit the brake pad fitting position?
After the job, select the option again in the same menu or apply the parking brake switch. The calipers return to normal and the warning lights go out.
Check these troubleshooting and repair guides for more help on your Mercedes-Benz.









