Mitsubishi Outlander Reset Oil Service Reminder
The service reminder on an Outlander is a mileage counter, not a measurement of how worn the oil actually is, so reset it only once the oil has genuinely been changed. The procedure is a button sequence on the dash, and the display drops back to the previous screen if you pause for about ten seconds, which is why it often takes two attempts.
At a Glance
- Message: Routine Maintenance Required, with a wrench icon on the Outlander’s display.
- Ignition must be OFF; the reminder cannot be reset with it on.
- Press the info switch on the cluster until the wrench screen appears.
- Hold it for about 2 seconds until the wrench flashes, then press again to confirm the reset.
- Reset only after the service is actually done.
Symptoms
The “Routine Maintenance Required” message appears on the Mitsubishi Outlander’s Dashboard.
Procedure
- Turn the ignition (or the operation mode on push button models) OFF. Mitsubishi’s owner’s manual states that the reminder cannot be reset while the ignition is ON.
- Lightly press the multi information display switch (the small info button on the instrument cluster) a few times until the service reminder screen with the wrench icon appears.
- Press and hold the switch for about 2 seconds until the wrench icon starts flashing. If you wait about 10 seconds without pressing anything, the display goes back to the previous screen.
- While the wrench icon is flashing, lightly press the switch once. The display changes from
---to CLEAR, then shows the time until the next service. - Start the engine to check if the reminder is cleared; if the “Routine Maintenance Required” message is no longer displayed, then you are done.
A Mitsubishi Outlander requires periodic oil maintenance to prevent the engine from developing premature wear like any other vehicle. Use the oil change interval in your Outlander’s maintenance booklet, and use the severe service interval if you mostly drive short trips, tow, or drive in dust or extreme heat.
🔧 Find out what is actually wrong before you pay someone to guess
Dealer level diagnostics at home with the YOUCANIC UCAN-II Pro.
- ✔ Covers most makes and models, including many luxury brands. Send us your VIN and we will confirm your car before you order
- ✔ Reads every module, not just the engine, so you find the faults a basic reader says are not there
- ✔ Commands the car: test a fan or pump, bleed ABS, retract an electronic parking brake, register a battery
- ✔ No subscriptions. Free lifetime updates, so the price you pay is the whole price
- ✔ Backed by real mechanics in the USA you can email before and after you buy
Featured in The Wall Street Journal
For instructions on how to replace the oil and oil filter of your Mitsubishi Outlander, you may go to our Mitsubishi 2.4L Engine Oil Change guide. After changing the oil and the oil filter, reset the Oil Service Interval counter using the steps above.
Resetting the Maintenance Reminder using the YOUCANIC UCAN-II Pro
If you’re having difficulty resetting the maintenance reminder manually, the YOUCANIC UCAN-II Pro can easily reset it. It can also read and clear fault codes, bi-directional tests, and many more.

Applications
- Mitsubishi Outlander 2006 to 2020
Reset the reminder only after the oil is changed
The service reminder is a simple mileage counter, not a measurement of how worn the oil actually is. Resetting it without changing the oil removes the only prompt you have and makes it very easy to run well past the interval, which is how engines end up with sludge and worn timing chain components.
If the reminder will not clear
Work through the button sequence again and watch the timing closely, since the reset usually requires holding the trip button while the ignition is switched, and releasing a moment early is the most common reason it fails. Make sure you are in the right display mode before starting.
If it still will not reset after several attempts, or the message returns on the next start, the instrument cluster may need the reset performed through the diagnostic port instead. A full system scanner can carry out the oil service reset directly on the cluster, which also works on models where the button method was never supported.
You almost certainly do not need a scan tool for this
The procedure above is done from the dashboard with the car stationary. No tool, no app, no port, no cost. If that is why you came to this page, you are finished, and anyone telling you this reset requires a diagnostic tool is selling something.
There is exactly one situation where a tool enters the picture, which is the one covered above where the reminder will not clear. If the dash procedure has failed more than once and the reminder stays, something is stored that the dash cannot see, and reading it is the next step. For that single occasion, rent one for seven days or have it read at a shop. Do not buy a scan tool to reset an oil reminder.
Frequently Asked Questions
What is the recommended oil for a Mitsubishi Outlander?
It depends on the engine and model year. Many later four cylinder Outlanders call for 0W-20, while older models and the V6 often call for a different grade. The correct grade is printed in your owner’s manual and usually on the oil filler cap.
How long can I drive after the oil change light comes on?
The reminder is a distance and time counter set to the service interval, so it means the oil is due, not that it has failed. Book the change soon and check the level on the dipstick in the meantime. Do not keep resetting it without changing the oil.
How often does a car need an oil change?
Follow the interval in your Outlander’s maintenance booklet, and use the severe service interval if you mostly drive short trips, tow, or drive in dust or extreme heat.


