Troubleshooting Chevy Check Engine Light

In this guide, we will be going over common problems that can trigger Chevrolet check engine light(s) to appear and diagnose the issue(s) yourself. 

What does the Check Engine light mean on a Chevy?  

chevrolet check engine light on

When your Chevrolet check engine light stays on, it means that the On-Board Diagnostic (OBD) system has detected a problem with the engine, emission system, or transmission. A fault code is stored in the Engine Control Unit (ECU). 

Chevy check engine light should only be on for a few seconds when you turn on the ignition and should turn off once the engine fully starts. If your Chevy check engine light stays on or is flashing, get the vehicle diagnosed as possible. 

Chevrolet check engine lights may also be referred to as Malfunction Indicator Lamps.

Symptoms

chevy engine car shakes and check engine light on

Common symptoms include:

  • Engine shaking
  • Poor throttle response
  • A decrease in fuel economy
  • Engine misfire
  • Difficulty accelerating
  • Car won't stay running
  • Check engine light flashing

Chevy check engine lights may stay on, but with no performance symptoms. Even if there are no symptoms, it is important to read the fault codes to determine why there is a CEL on.

Common problems that cause Chevy check engine light to come on 

Loose gas cap triggers chevy check engine light

Common problems that can trigger Chevy check engine lights to stay on include: 

  • Loose gas cap / damaged seal
  • Faulty Mass Air Flow (MAF) sensor
  • Spark Plugs
  • Faulty ignition coil
  • Bad oxygen (O2) sensor
  • Dirty fuel injector
  • Bad fuel filter or pump
  • Catalytic converter
  • EVAP leak

First, check the gas cap and make sure it is on tight. If the light doesn't reset within the next two to three days, read the fault codes. 

How to Reset Check Engine Light on a Chevy? 

Follow the instructions below to learn how to read and reset the Chevrolet service engine light codes. For this procedure, you will need an OBD-II scanner. You should only reset the check engine light and codes after all necessary repairs are completed. 

  1. Locate the diagnostic port under the dashboard of your Chevrolet on the driver's side. This is a 16-pin port on all 1996, and newer Chevrolet vehicles have this port. Plug in your OBD2 scanner or Bluetooth adapter into the port. Chevrolet  Check Engine Light ON Troulbeshooting
  2. Turn the ignition ON, key in position II. All Chevrolet dashboard lights will turn on but do not start the engine. If your Chevrolet has Start/Stop button, you will need to press the START button without pressing the brakes. How to diagnose Chevrolet  check engine light service engine soon Spark, Sonic, Bolt, Volt, Cruze, Malibu, Impala, Camaro, Corvette, City Express, Trax, Equinox, Traverse, Tahoe, Suburban, Colorado, Silverado, Sonic, Blazer, Astro, HHR, Uplander, Avalanche etc.
  3. Allow your OBD2 scanner to turn on and connect to your Chevrolet Engine Control Unit (ECU). This step can take up to one minute. Check Engine Light On Chevrolet
  4. Read Chevrolet check engine light codes from the Engine Control Unit (ECU) using an OBD-II scanner.
  5. Once you have retrieved the codes, write them down. Research the codes and fix the underlying problem, you can come back and click Erase Codes to reset the Chevrolet check engine light. erase Chevrolet  check engine light Spark, Sonic, Bolt, Volt, Cruze, Malibu, Impala, Camaro, Corvette, City Express, Trax, Equinox, Traverse, Tahoe, Suburban, Colorado, Silverado, Sonic, Blazer, Astro, HHR, Uplander, Avalanche etc.

The fault codes are just the starting point. Research every present code and common problem. Don't replace parts based on the fault code only. Get the opinion of a professional mechanic before replacing any parts. 

Comments

Visitor, August 20, 2019
My Chevrolet Cruze 2012 when engine is running engine light still on and is coming to the mechanical
The content of this field is kept private and will not be shown publicly.

Plain text

  • No HTML tags allowed.
  • Lines and paragraphs break automatically.
  • Web page addresses and email addresses turn into links automatically.